Design and Implementation of IOT-Based Intravenous (IV) Bag Monitoring and Alert System
- Authors
-
-
Gregory T. AKAU
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Abel AIROBOMAN
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Nathaniel DALLA
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
- Keywords:
- Intravenous (IV) monitoring, IoT-based healthcare, Arduino Uno, drip rate monitoring, ESP8266 Wi-Fi, ThingSpeak cloud, hospital automation.
- Abstract
-
Health, being a critical aspect of daily life, demands heightened attention, especially when a patient is hospitalized. In densely populated hospitals with limited nursing staff, the continuous monitoring of Intravenous (IV) fluid becomes a challenge. If the IV fluid is not properly monitored, severe consequences may arise, such as blood reflux or the entry of air bubbles into the patient's bloodstream when the fluid bottle runs dry. To address this, the project proposes the design and implementation of an IoT-based intravenous infusion monitoring and Alert System using the Huamao Communication 12 radio frequency module (HC-12) for wireless communication. The system also integrates Espressif Wi-Fi SoC ESP8266 wi-fi connectivity for real-time data transmission to the ThinkSpeak cloud platform. The hardware setup includes a load cell with an HX711 interface for continuous measurement of the IV fluid's weight, and a laser sensor positioned on the drip chamber to monitor the droplet rate. An Arduino Uno microcontroller coordinates the sensors and decision logic. When the fluid level drops below a critical threshold or the drip rate becomes abnormal, an alert is transmitted wirelessly via the RF module to a remote receiver unit (e.g., nurse’s station), where the patient's information and alert status are displayed. Additionally, the ESP8266 module uploads real-time data to the internet for remote monitoring and analytics. The performance evaluation of the prototype demonstrated a system success rate of approximately 96.8% in accurately detecting both low-fluid and abnormal drip rates. This low-cost, easily deployable system enhances patient safety by ensuring timely intervention from medical staff and is particularly suited for resource-constrained hospitals that cannot afford expensive commercial IV monitoring system.
- References
- Downloads
- Published
- 15-11-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Muhammad B. MUHAMMAD, Noor S. B. MANSOR, Fariha R. KHAN, Investigating Breakdown Strength Based on Trapping Profile in Cross-Linked Polyethylene (XLPE) Nanocomposites , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Dauda ALI, Auwal SHUAIBU, Design and Performance Evaluation of Plastic–Sand Interlocking Blocks Using Waste Polyethylene Terephthalate (PET) and Low-Density Polyethylene (LDPE) for Sustainable Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Usman A. ABDURRAHMAN, Abdulkadir A. BICHI, Usman HARUNA, Akibu M. ABDULLAHI, A Hybrid Graph Neural Network Framework Integrating Handcrafted Features for Real-Time Iris Recognition in Motion , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Gbenga G. OSEKE, Chisom S. AMADI, Abubakar U. RAJI, Hydrogen Production from Flare Gas via Steam Methane Reforming: A Simulation-Based Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Nuhu MOHAMMED, Garkuwa Y. ADAMU, Abubakar A. FACHWAY, Aminu MOHAMMED, Afolayan A. OLASUNKANMI, Odoh F. CHIMEZIE, Muhammad A. YUSUF, Development of A Water-Recycling Pico Hydropower System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Francis O. BOROKINNI, Olarewaju T. OGINNI, Ridwan O. RAJI, Kolawole ALONGE, Effects of Quenching Media and Heat Transfer Rate on the Hardness and Microstructure of Low-Carbon Steel , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abdulkabiru A. ABDULRAZAQ, Abideen A. ISMAIL, Muhammad S. NAZRUL-ISLAM, Akeem R. ABIOYE, Margaret D. OKPOR, Paschal, U. CHINEDU, Image Denoising: An Overview of Noise Model, Denoising Methods and Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Idris M. WADA, Abba IBRAHIM, Genesis ISHAYA, Performance Evaluation of Climate Products with Validation Using Bootstrapping and Climate Extremes in the Hadejia-Jama’are River Basin, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yusuf M. YAHAYA, Factors Contributing to the Erosion of Freehand Sketching Competence in Technology Education: A Case Study of Bayero University, Kano , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Johnson O. ADEOGO, Olawale J. OLALUYI, Olumuyiwa A. OJO, Abayomi T. AYODELE, Elijah A. OLAJUYIN, Fasasi BELLO, Paul C. OFODU, Performance Evaluation of 3.5 kVA Hybrid Inverter Following Standard Engineering Practices and Safety Procedures , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
