Design and Implementation of IOT-Based Intravenous (IV) Bag Monitoring and Alert System
- Authors
-
-
Gregory T. AKAU
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Abel AIROBOMAN
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Nathaniel DALLA
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
- Keywords:
- Intravenous (IV) monitoring, IoT-based healthcare, Arduino Uno, drip rate monitoring, ESP8266 Wi-Fi, ThingSpeak cloud, hospital automation.
- Abstract
-
Health, being a critical aspect of daily life, demands heightened attention, especially when a patient is hospitalized. In densely populated hospitals with limited nursing staff, the continuous monitoring of Intravenous (IV) fluid becomes a challenge. If the IV fluid is not properly monitored, severe consequences may arise, such as blood reflux or the entry of air bubbles into the patient's bloodstream when the fluid bottle runs dry. To address this, the project proposes the design and implementation of an IoT-based intravenous infusion monitoring and Alert System using the Huamao Communication 12 radio frequency module (HC-12) for wireless communication. The system also integrates Espressif Wi-Fi SoC ESP8266 wi-fi connectivity for real-time data transmission to the ThinkSpeak cloud platform. The hardware setup includes a load cell with an HX711 interface for continuous measurement of the IV fluid's weight, and a laser sensor positioned on the drip chamber to monitor the droplet rate. An Arduino Uno microcontroller coordinates the sensors and decision logic. When the fluid level drops below a critical threshold or the drip rate becomes abnormal, an alert is transmitted wirelessly via the RF module to a remote receiver unit (e.g., nurse’s station), where the patient's information and alert status are displayed. Additionally, the ESP8266 module uploads real-time data to the internet for remote monitoring and analytics. The performance evaluation of the prototype demonstrated a system success rate of approximately 96.8% in accurately detecting both low-fluid and abnormal drip rates. This low-cost, easily deployable system enhances patient safety by ensuring timely intervention from medical staff and is particularly suited for resource-constrained hospitals that cannot afford expensive commercial IV monitoring system.
- References
- Downloads
- Published
- 15-11-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Samuel E. CHUKWU, Martins Y. OTACHE, Precious O. ATEMOAGBO, Emmanuel O. AGBESE, Copula-Based Modelling of Drought Severity-Duration-Frequency Relationship of Sokoto-Rima-River Basin, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Muhammad B. MUHAMMAD, Noor S. B. MANSOR, Fariha R. KHAN, Investigating Breakdown Strength Based on Trapping Profile in Cross-Linked Polyethylene (XLPE) Nanocomposites , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Usman A. ABDURRAHMAN, Abdulkadir A. BICHI, Usman HARUNA, Akibu M. ABDULLAHI, A Hybrid Graph Neural Network Framework Integrating Handcrafted Features for Real-Time Iris Recognition in Motion , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Hafsah A. ABDULRAHMAN, Muhammad M. HAMIDU, Techno-Economic Optimization of a Hybrid PV-Wind-Waste-to Energy System for the University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Jennifer BALA, Sikiru O. SUBAIRU, Noel M. DOGONYARO, Joseph A. OJENIYI, Suleiman AHMAD, Development of an Optimized Hybrid XGBoost–GRU Model for Detection of Ponzi Schemes in Ethereum Transaction Networks , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Kazeem A. BELLO, Adeniyi O. ADESINA, Lukman A. OPEYEMI, Solomon O. UVIASE, Francis O. BOROKINNI, Friday ONUH, Tunde O. OGUNDANA, Adebayo I. OLUMOROTI, Developments and Applications of Additive Manufacturing in the Automotive Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chukwuemeka S. IBEH, Abubakre O. KAMARDEEN, Saka A. ABDULKAREEM, Aliyu A. ABDULLAHI, Experimental Study on the Characterisation and Thermo-Physical Properties of Graphene-Agro Based Hybrid Nanofluids , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Danladi K. GARBA, Emmanuel O. AWEDA, Nuhu A. ADEMOH, Fredrick NGOLEMASANGO, Pascal A. UBI, Akor TERNGU, Lawal KABIR, Shuaibu O. YAKUBU, The Effects of Gum Arabic Matrix on the Hardness and Water Absorption of Agro-Based (Banana Pseudostem) Hybrid Composites , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Peter EDOKA, Incidents of Flood Disaster in Kaduna: Preventive and Mitigating Measures , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bolaji A. OMODUNBI, Hammed A. OLASUNKANMI, Development of an Ensemble Model for Email Filtering and Classification , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
