Design and Implementation of IOT-Based Intravenous (IV) Bag Monitoring and Alert System
- Authors
-
-
Gregory T. AKAU
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Abel AIROBOMAN
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
Nathaniel DALLA
Department of Electrical/Electronics, Nigerian Defence Academy, Kaduna, Nigeria
Author
-
- Keywords:
- Intravenous (IV) monitoring, IoT-based healthcare, Arduino Uno, drip rate monitoring, ESP8266 Wi-Fi, ThingSpeak cloud, hospital automation.
- Abstract
-
Health, being a critical aspect of daily life, demands heightened attention, especially when a patient is hospitalized. In densely populated hospitals with limited nursing staff, the continuous monitoring of Intravenous (IV) fluid becomes a challenge. If the IV fluid is not properly monitored, severe consequences may arise, such as blood reflux or the entry of air bubbles into the patient's bloodstream when the fluid bottle runs dry. To address this, the project proposes the design and implementation of an IoT-based intravenous infusion monitoring and Alert System using the Huamao Communication 12 radio frequency module (HC-12) for wireless communication. The system also integrates Espressif Wi-Fi SoC ESP8266 wi-fi connectivity for real-time data transmission to the ThinkSpeak cloud platform. The hardware setup includes a load cell with an HX711 interface for continuous measurement of the IV fluid's weight, and a laser sensor positioned on the drip chamber to monitor the droplet rate. An Arduino Uno microcontroller coordinates the sensors and decision logic. When the fluid level drops below a critical threshold or the drip rate becomes abnormal, an alert is transmitted wirelessly via the RF module to a remote receiver unit (e.g., nurse’s station), where the patient's information and alert status are displayed. Additionally, the ESP8266 module uploads real-time data to the internet for remote monitoring and analytics. The performance evaluation of the prototype demonstrated a system success rate of approximately 96.8% in accurately detecting both low-fluid and abnormal drip rates. This low-cost, easily deployable system enhances patient safety by ensuring timely intervention from medical staff and is particularly suited for resource-constrained hospitals that cannot afford expensive commercial IV monitoring system.
- References
- Downloads
- Published
- 15-11-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olawale J. OLALUYI, Johnson O. ADEOGO, Adeniyi O. AJIBOYE, Mayowa O. ORESELU, Olarewaju T. OGINNI, Application of Machine Learning for Enhancing Fake Logo Detection , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sarafa ISHOLA, Olusegun S. OLAOYE, Adeyinka A. ADEGBOLA, Isaac A. OLUREMI, Oluseye O. AGBEDE, Drying Kinetics and Combustion Characteristics of Carbonized Cashew Nut Shell Briquettes Under Open Sun, Passive and Active Solar Drying , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Caleb A. ABORISADE, Jide E.T. AKINSOLA, Ifeoluwa M. OLANIYI, Fathia O. ONIPEDE, Emmanuel A. OLAJUBU, Ganiyu A. ADEROUNMU, Machine Learning-Based Polycystic Ovary Syndrome Generative Modelling via Ensemble Learning and Neural Networks for Infertility Prediction , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Usman A. ABDURRAHMAN, Abubakar A. ROGO, Abdulkadir A. BICHI, Akibu M. ABDULLAHI, Beyond Overload: Assessing Cognitive Load to Facilitate Learning Transfer in Virtual Environments , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Samuel E. CHUKWU, Martins Y. OTACHE, Precious O. ATEMOAGBO, Emmanuel O. AGBESE, Copula-Based Modelling of Drought Severity-Duration-Frequency Relationship of Sokoto-Rima-River Basin, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Muhammad B. MUHAMMAD, Noor S. B. MANSOR, Fariha R. KHAN, Investigating Breakdown Strength Based on Trapping Profile in Cross-Linked Polyethylene (XLPE) Nanocomposites , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Usman A. ABDURRAHMAN, Abdulkadir A. BICHI, Usman HARUNA, Akibu M. ABDULLAHI, A Hybrid Graph Neural Network Framework Integrating Handcrafted Features for Real-Time Iris Recognition in Motion , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nuhu MOHAMMED, Garkuwa Y. ADAMU, Abubakar A. FACHWAY, Aminu MOHAMMED, Afolayan A. OLASUNKANMI, Odoh F. CHIMEZIE, Muhammad A. YUSUF, Development of A Water-Recycling Pico Hydropower System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Danladi K. GARBA, Emmanuel O. AWEDA, Nuhu A. ADEMOH, Fredrick NGOLEMASANGO, Pascal A. UBI, Akor TERNGU, Lawal KABIR, Shuaibu O. YAKUBU, The Effects of Gum Arabic Matrix on the Hardness and Water Absorption of Agro-Based (Banana Pseudostem) Hybrid Composites , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
