Waste Management in Bauchi Metropolis: Solid Measure and Characterization in Municipality
- Authors
-
-
Samaila J. EL-PATEH
Bauchi State Ministry of Water Resources, Bauchi, Bauchi State, Nigeria
Author
-
Ibrahim IDRIS
Kano State Ministry of Water Resources, Kano, Kano State, Nigeria
Author
-
- Keywords:
- Solid waste, waste characterization, waste components, household waste.
- Abstract
-
The research examined waste management in order to prevent diseases in the Bauchi city, Bauchi local government in Bauchi state of Nigeria by technical and scientific approach to utilized generated solid of waste; that is physical composition of refuse dumped out of small, medium enterprises and communities. The study exhausted more than twelve-week when conducting questionnaire, interviews and survey that employed in the collection of the required data. According to National Population Commission (2006) population of Bauchi metropolis and its environs has growth rate of 3.2% annually which identified different percentage embedded to solid waste disposals; composition of dirt, ash and other unidentified objects was 20.2%, paper/cardboard 14.1%, nylon and polythene 16.4%, garden leaves 13.5%, food waste 11.6% while tin cans/metals were 5.1%, textile/fabrics 6.2%, plastic/rubber 6.8% and lastly glass and ceramics waste 6.1%. Over 80% of the waste fraction has the potential for recovery into other products; with this, 42.4% could be recycled and 51.56% suitable for biological conversions such as composting and anaerobic digestion, expected solid waste accumulated in Bauchi capital city daily was 0.30 kg/cap/day, the solid waste management studies may guide stakeholders to pick positive decisions on waste management options.
- References
- Downloads
- Published
- 24-09-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Koliya LAAYE, Solomon O. OGUCHE, Ibrahim I. JIDDA, Abdullahi A. ADAMU, Economic Viability of Waste-to-Energy: Pathways for Sustainable Power Generation in Jalingo, Taraba State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sirajo ALHASSAN, Abdullahi A. ADAMU, Mohammed T. JIMOH, Experimental Characterization and Seasonal Energy Potential Assessment of Municipal Solid Waste in Kano City, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Benedict O. EDENSETING, Innocent O. OBOH, Alexander A. JOCK, Effective Food Waste Utilization: A Veritable Source of Biofuel for Nigerian Economic Sustenance and Development - A Review , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Hafsah A. ABDULRAHMAN, Muhammad M. HAMIDU, Techno-Economic Optimization of a Hybrid PV-Wind-Waste-to Energy System for the University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Oyeyemi T. AFOROLAGBA-BALOGUN, Olumide A. TOWOJU, Characterization of Fuel Produced from Nylon (Polyamide) and Polyethylene Terephthalate (PET) Wastes with Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sirajo ALHASSAN, Abdullahi A. ADAMU, Mohammed T. JIMOH, Multi-Criteria Decision Analysis and Optimization Approaches in Sustainable Waste-to-Energy Planning: A Systematic Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ndagi MAMUDU, Ibrahim S. MOHAMMED, Peter DANIEL, Timothy Y. AKANDE, Bala A. GARBA, Development and Performance Evaluation of Biomass Pyrolysis System for Biofuel Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kazeem A. BELLO, Adeniyi O. ADESINA, Lukman A. OPEYEMI, Solomon O. UVIASE, Francis O. BOROKINNI, Friday ONUH, Tunde O. OGUNDANA, Adebayo I. OLUMOROTI, Developments and Applications of Additive Manufacturing in the Automotive Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mathew O. ADEOTI, Victor N. HARUNA, Omolayo M. IKUMAPAYI, Timothy A. ADEKANYE, Development and Characterization of Epoxy-Based Asbestos-Free Brake Pad Composites Reinforced with Cow Hoof Particulates , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
