Modelling and Performance Optimization of a Dual Fuel Mode Power Generation System (A Case Study of Allanblackia floribunda Seed Oil)
- Authors
-
-
Ayodeji T. BALOGUN
Author
-
Onoghwarite E. OHIMOR
Department of Chemical Engineering, Federal University of Petroleum Resources, Effurun, Delta State, Nigeria
Author
-
Adegboyega L. ALUKO
Author
-
- Keywords:
- Modelling; Optimization; Performance, Allanblackia floribunda Seed Oil.
- Abstract
-
This study focuses on the optimization of a small-scale, spark-ignition power generation system operating on a dual fuel arrangement of petrol and Liquefied Petroleum Gas (LPG) The research addresses the challenge of calibrating such systems for optimal performance, which volves balancing often conflicting objectives like fuel efficiency, power output, and emissions A Response Surface Methodology (RSM) framework, employing a Central Composite Design (CCD) of experiments, was used to investigate the effects of five key operating parameters Engine Load, Generator Speed, Ignition Timing, Air-Fuel Ratio, and Compression Ratio Empirical quadratic models were developed and validated to predict key responses Brake Thermal Efficiency (BTE), Specific Fuel Consumption (SFC), Carbon Monoxide (CO), and Nitrogen Oxides (NOx) emissions, and Power Output The Desirability Function Approach was then applied for multi-response optimization to identify the bestcompromise operating conditions for both petrol and LPG modes. The results demonstrate that while both fuels can achieve nearly identical thermal efficiency at their respective optima, LPG operation enables a 22 9% higher power output. However, this is accompanied by a 5.56% increase in mass-based fuel consumption and significant increases in CO (66.2%) and NOx (14.1%) emissions under the high-load optimization strategy The study concludes that LPG is a superior fuel for applications demanding high power density, provided that the increased emissions are managed through targeted calibration or after-treatment, the Allanblankia florrbunda Seed Oil was used as case study, thereby offering a viable path for cleaner and more powerful decentralized electricity generation.
- References
- Downloads
- Published
- 25-09-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Ayodeji T. BALOGUN, Onoghwarite E. OHIOMOR, Adegboyega L. ALUKO (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Titilope A. BANJOKO, Bilkisu L. MUHAMMAD-BELLO, Predicting Requirement Change Using Bayesian Networks on Historical Traceability Data , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Ephraim G. KEFAS, Abdulfatai JIMOH, Mohammed A. EVUTI, Abubakar A. IBRAHIM, Abdulwahab GIWA, Adeola G. OLUGBENGA, Luffa Sponge, Banana Stem and Delonix regia Seed Characterization as Potential Biosorbents for Industrial Wastewater Remediation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Shamsuddeen J. AHMAD, Saifullahi S. SADI, Muhammad M. AHMAD, Abdullahi D. UMAR, Shamsuddeen USMAN, Comparative Analysis of Machine Learning Algorithms for the Detection and Classification of Suspicious Emails , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Habibat O. YUSUFU, Yakubu D. MOHAMMED, Rose JONATHAN, Shamsuddeen SULAIMAN, Impact of Health and Safety Management on Safety Performance of Small and Medium-Sized Construction Firms in Abuja , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Zachariah S. PYENDANG, Felix ACHEMA, Isheni YAKUBU, Solomon E. APEH, Microstructural Characterization of Fibre Reinforced Polymer (FRP) Composite (Kenaf Fibre and Polyester Resin) for Structural Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Joseph K. ZAMBWA, Jibril M. KAURA, Ocholi AMANA, Abdrasheed S. ABDURASHEED, Ejembi WILLIAMA, Evaluation of Materials and Performance Characteristics of Tannery Sludge Crumb Rubber Concrete (TSCRC) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Oyeyemi T. AFOROLAGBA-BALOGUN, Olumide A. TOWOJU, Characterization of Fuel Produced from Nylon (Polyamide) and Polyethylene Terephthalate (PET) Wastes with Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ojo I. ENOCK, Ibrahim A. SAIDU, Ibrahim SULAIMAN, Oluwafeyisikemi. Y. ENOC, Design and Development of a Melon Shelling Machine , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Johnson O. ADEOGO, Olawale J. OLALUYI, Olumuyiwa A. OJO, Abayomi T. AYODELE, Elijah A. OLAJUYIN, Fasasi BELLO, Paul C. OFODU, Performance Evaluation of 3.5 kVA Hybrid Inverter Following Standard Engineering Practices and Safety Procedures , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Fatima A. MUSA, Abdulmajid B. UMAR, Abba M. BALA, A Hybrid CNN–BiGRU Model with Grey Wolf Optimization and LightGBM for Stock Price Prediction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
