Development of an IoT-Based Smart Distribution Transformer Monitoring System for Reliable Rural Electrification
- Authors
-
-
Olalekan OGUNBIYI
Author
-
Lambe M. ADESINA
Author
-
Ibrahim Z. ARIYO
Author
-
- Keywords:
- Condition monitoring, Distribution transformer, Internet of Things (IoT), Remote monitoring, Rural electrification.
- Abstract
-
Distribution transformers are essential components of electric power distribution networks, and their reliable operation depends on continuous monitoring of critical operating parameters. However, conventional inspection techniques are periodic, labour-intensive, and incapable of providing the real-time information required for proactive maintenance. This study presents the design, implementation, and experimental validation of an Internet of Things (IoT)-based smart distribution transformer monitoring system for real-time acquisition and remote visualisation of transformer operating parameters. The developed system integrates isolated voltage and current sensing circuits, an Arduino Uno microcontroller, an ESP8266 Wi-Fi communication module, a 16 × 2 liquid crystal display (LCD), and the Blynk cloud platform for simultaneous local and remote monitoring. The sensing circuits were calibrated using polynomial and exponential regression models to improve measurement accuracy, while the complete hardware was designed, simulated, and verified using the PROTEUS Design Suite before fabrication. Experimental evaluation was conducted over a voltage range of 181–249 V and load currents up to 9 A. The developed system exhibited excellent agreement with calibrated reference instruments, recording a maximum voltage deviation of approximately 1 V (less than 0.5%) and a maximum current deviation of 0.1 A (approximately 1.1%). In addition, the estimated apparent power, real power, and power factor closely matched the reference values. The communication subsystem maintained stable Wi-Fi connectivity, achieving a data transmission success rate exceeding 99% with dashboard refresh times below 2.1 s, thereby enabling reliable real-time cloud monitoring. The proposed monitoring system provides a low-cost, accurate, and scalable solution for continuous condition monitoring of distribution transformers and offers significant potential for predictive maintenance and intelligent asset management in modern smart grid applications.
- References
- Downloads
- Published
- 07-09-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Olalekan OGUNBIYI, Lambe M. ADESINA, Ibrahim Z. ARIYO (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Sindrella AWINO, Peter ADEOYE, Application of Integrated Solar-Powered Ultraviolet Radiation and Sand Biofiltration Techniques in Rural Water Treatment: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Muhammad B. MUHAMMAD, Muhammad Y. ABDULLAHI, Aminu BALA, Optimal Reduction of Technical Power Losses in Radial Distribution Networks Using Differential Evolution for Distributed Generation: A Case Study of the Azare Substation in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Tunji J. ERINLE, Daniel C. UGURU-OKORIE, Abiodun M. ADEBIMPE, Adeolu A. ADEDIRAN, Hilary U. EZEA, A Comprehensive Review of In-Situ Monitoring and Post-Process Defect Detection in Additive Manufacturing , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Victor A. NSABA, Sabiu B. YUSUF, Kafayat A. IBRAHIM, Consumer Perceptions of Artificial Intelligence (AI)-Driven Smart Grids and Energy Efficiency in Northwest Nigeria’s Power Distribution Sector: A Multi-State Case Study of Sokoto, Kebbi, and Zamfara , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nnamdi S. OKOMBA, Adedayo A. SOBOWALE, Adebimpe O. ESAN, Bolaji A. OMODUNBI, Taiwo A. AWOYEMI, Development of a High Blood Pressure and Hypoxemia Measuring Device , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abdulkareem BELLO, Saleh S. LUKMAN, Tasie M. CHIZE, Yusuf O. ADEIZA, Chibuzor A. OKAFOR, Abdullahi O. YAKUBU, Design, Simulation, and 3D Printing of a Lightweight Drone Frame for Farm Monitoring , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Oluwayinka. G. AKINWAMIDE, Olugbenga O. AMU, Christopher FAPOHUNDA, Prediction of International Roughness Index of Flexible Pavement Using Machine Learning-Based Predictive Framework in Ekiti State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abba M. BALA, Abdurrauf G. SHARIFAI, Umar S. HARUNA, A Hybrid Deep Learning Model for Efficient Anomaly Detection in Video Surveillance Systems , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olusegun A. AFOLABI, Olanrewaju A. OLANITE, Nsikan L. AKPAN, Design and Simulation of a Synchronous Reference Frame-Based Active Power filter for Harmonic Mitigation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olawale J. OLALUYI, Johnson O. ADEOGO, Aduragbemi F. OJO, Olarewaju T. OGINNI, Design and Construction of Transistor Based Water Level Indicator Tank with Overflow Alarm , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
