Smart Fence for Real-Time Farm Protection in Sub-Saharan Africa Using Artificial Intelligence: A Systematic Review and Research Roadmap
- Authors
-
-
Omokhafe J. TOLA
Author
-
James G. AMBAFI
Author
-
Umar S. DAUDA
Author
-
- Keywords:
- Initial void ratio, natural moisture content, settlement, compression ratio, one-dimensional consolidation.
- Abstract
-
Agricultural insecurity from wildlife encroachment and crop raiding threatens food production in Sub-Saharan Africa (SSA), where 60% of smallholder farmers rely on agriculture. Conventional barbed wire and electric fences are passive, static, and poorly suited for rural SSA's resource-constrained environments. This paper presents a systematic review of smart fence technologies for real-time farm protection, adhering to PRISMA 2020 guidelines. From an initial 1,247 documents across IEEE Xplore, ScienceDirect, SpringerLink, and Google Scholar, 56 peer-reviewed studies (2008–2026) were selected for synthesis following title and abstract screening, duplication, and full-text eligibility assessment. The review classifies smart fences into four categories: sensor-based, vision-based, IoT-based, and hybrid AIoT-based. Under controlled conditions, YOLOv8 models outperformed others with over 92% detection accuracy. For edge deployments, MobileNetV3 achieved 85.7% accuracy on commodity hardware, consuming only 3.1 W. Critically, the study found no smart fence deployments in the literature validated specifically for SSA, highlighting a major gap given the region's unique infrastructural challenges. Key contributions of this paper include: (i) synthesizing AI and smart fence performance benchmarks; (ii) establishing a 12-factor matrix quantifying SSA deployment constraints by severity, prevalence, and technology readiness; (iii) proposing an SSA-specific edge-AI reference architecture optimized for solar power, low connectivity, and a sub-$400 deployment cost; and (iv) outlining a structured 3-level research roadmap aligned with TRL 4-9 milestones. This review provides a solid foundation for developing cost-effective, context-aware smart fencing tailored to SSA's agricultural realities.
- References
- Downloads
- Published
- 08-09-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Omokhafe J. TOLA, James G. AMBAFI, Umar S. DAUDA (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Oguntola J. ALAMU, Peter O. ILORI, Seun OYELAMI, Wasiu O. ADEDEJI, Tunji J. ADEPOJU, Abideen T. OYEWO, A Review of the Effect of Post-Processing Heat Treatment on 3D Printed Metal Parts , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Luqman K. SALATI, Sani D. MUHAMMAD, Jacob T. ADEYEMO, Simulation of Trucks Haulage Operation at Ashaka Cement Company in Gombe State, North-Eastern Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mohammed A. GANA, Zaka A. MSHELIA, Isuwa S. AJI, Alhaji GUJJA, Lawan A.M. KOLO, Investigation and Comparative Analysis of Natural Moulding Sands from Five Deposits in Maiduguri, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yusuf L. SHUAIB-BABATA, Kabiru S. AJAO, Yusuf O. BUSARI, Ibrahim O. AMBALI, Kehinde O. ARUNA, Henrietta O. COKER, Toheeb A. NURUDEEN, Evaluation of UNILORIN Dam Moulding Sand Properties for Foundry Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Babagoni A. ADAM, Muhammad B. MAINA, Muhammad SHUWA, Abba B. MUHAMMAD, A Review on Neem Leaves Valorization Through Advanced Briquetting and Carbonization Technologies , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar S. MOHAMMED, Mohammed ALIYU, Mohammed U. GARBA, Ibrahim S. MOHAMMED, Ibrahim A. KUTI, Meshack S. IMOLOGIE, Umaru MUSA, Olalekan D. ADENIYI, Peter A. ADEOYE, Abubakar G. ISAH, Folarin T. OLORUNMOTITO, Development and Packaging of Eco-friendly Biosolid Briquettes Synthesised with Bagasse for Green Energy Generation and Utilisation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bala YAHAYA, Mukhtar N. YAHYA, Characterization of Soil Properties Under Continuous Irrigation Practice , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Vincent B. ONIGBARA, Muftau A. GBENLE, Sunday I. AGU, Mechanical and Biological Performance of Titanium Hydroxyapatite Composites for Biomedical Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Obafemi A. IBITOYE, Jemimah O. TOLU-ALALADE, Solar-Powered Low-Cost Housing: Designing Off-Grid Communities with Interlocking Stabilised Soil Blocks (ISSB) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Omokhafe J. TOLA, Garba AMBAFI, Emmanuel C. OBUAH, Isah N. ABUBAKAR, Mutiat S. YISA, Development of Energy-Aware Hamiltonian-Based Fixed-Time Chaos Control and Synchronisation of Brushless DC Motor for Electric Vehicle Application , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
