Design and Analysis of a Dual-Band Circular Microstrip Antenna Using Spatially Distributed CSRRs
- Authors
-
-
Israel A. OLUWAFEMI
Author
-
Akaninyene B. OBOT
Author
-
Emmanuel UBOM
Author
-
Ayodele A. OLATUNJI
Author
-
Mbuotidem G. ROBINSON
Author
-
- Keywords:
- Dual band, Circular microstrip antenna, CSRR, Bandwidth, Directivity, 5G.
- Abstract
-
Previous studies on metamaterial-integrated Circular Microstrip Antennas (CMSAs) for 5G applications have reported improvements in radiation characteristics, while bandwidth enhancement has remained a design challenge. This study investigates the effect of Complementary Split-Ring Resonator (CSRR) number and spatial arrangement on the impedance characteristics of a circular microstrip antenna operating over 3.4–4.2 GHz. The antenna was designed and simulated using CST Studio Suite on an FR-4 substrate with a relative permittivity of 4.4 and thickness of 1.6 mm. A conventional CMSA was first established as the baseline, after which several CSRR configurations involving the circular patch and ground plane were investigated. The selected configuration consists of one CSRR incorporated into the circular patch and three CSRRs arranged in a “>” configuration on the ground plane. The resulting antenna exhibits two −10 dB impedance bands from 3.7056–3.8848 GHz and 3.984–4.200 GHz, corresponding to bandwidths of 179.2 MHz and 216.0 MHz, respectively. Within the simulated frequency range, the aggregate accepted bandwidth is 395.2 MHz, compared with 352.8 MHz for the baseline CMSA. The selected configuration also produces a maximum simulated directivity of 5.265 dBi at 3.9 GHz. The comparative results show that the impedance response is strongly affected by the number and spatial distribution of the CSRRs. The simulation results show that an appropriate spatial arrangement of CSRRs can provide dual-band operation while maintaining satisfactory simulated radiation characteristics.
- References
- Downloads
- Published
- 31-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Israel A. OLUWAFEMI, Akaninyene B. OBOT, Emmanuel UBOM, Ayodele A. OLATUNJI, Mbuotidem G. ROBINSON (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Johnson O. ADEOGO, Olawale J. OLALUYI, Olumuyiwa A. OJO, Abayomi T. AYODELE, Elijah A. OLAJUYIN, Fasasi BELLO, Paul C. OFODU, Performance Evaluation of 3.5 kVA Hybrid Inverter Following Standard Engineering Practices and Safety Procedures , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ayodele S. OLUWOLE, Olumayowa A. OJO, Olaitan AKINSANMI, Model Selection for Path Loss Prediction of Ultra High Frequency Terrestrial Television , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Kingsley C. IGWE, Abubakar T. MUHAMMAD, Obiseye OBIYEMI, Abiodun S. MOSES, Aku G. IBRAHIM, Joel A. EZENWORA, Julia O. EICHIE, Real-Time Evaluation of Rain-Induced Signal Degradation on Digital Satellite Television Links in Minna, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Oyeyemi T. AFOROLAGBA-BALOGUN, Olumide A. TOWOJU, Characterization of Fuel Produced from Nylon (Polyamide) and Polyethylene Terephthalate (PET) Wastes with Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Gbenga G. OSEKE, Chisom S. AMADI, Abubakar U. RAJI, Hydrogen Production from Flare Gas via Steam Methane Reforming: A Simulation-Based Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Tahiru MOHAMMED, Muhammad B. MAINA, Abba B. MUHAMMAD, Muhammad SHUWA, From Local Sand to Functional Silicon: An Integrated Pathway for Producing Photovoltaic-Grade Material from Nigerian Silica Sand , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mohammed U. GARBA, Usman B. ABDULLAHI, Hayatudden S. BARAYAIS, Aisha B. FARUQ, Suleiman IDRIS, Abubakar M. MUHAMMAD, Abubakar S. MOHAMMED, Treatment of Gold Mining Wastewater: A Review of Current Technologies and Future Perspectives , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abdulkareem BELLO, Saleh S. LUKMAN, Tasie M. CHIZE, Yusuf O. ADEIZA, Chibuzor A. OKAFOR, Abdullahi O. YAKUBU, Design, Simulation, and 3D Printing of a Lightweight Drone Frame for Farm Monitoring , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Johnson O. ADEOGO, Examination of Electromagnetic Radiation Intensity of 5G Mobile Transceivers Based on Its Operational Techniques , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
