Decline Curve Analysis of Continuous Injection Gas Lifted Wells
- Authors
-
-
Ayodele DANIEL
Author
-
Mercy O. AKEJU
Author
-
Sunday O. ISEHUNWA
Author
-
Abel A. ADEYI
Author
-
Adebayo T. OGUNYEMI
Author
-
- Keywords:
- Decline curve analysis, Developed reserves, Production rate, Gas lift, Arps’ exponential model.
- Abstract
-
Decline Curve Analysis is one of the established techniques for reservoir performance evaluation and estimation of developed reserves. While it has been well utilized for natural drive production, there have been challenges in accurate evaluation of gas lifted wells because of additional energy that supplements the natural which changes future production rate of the reservoir and distorts the reservoir’s production decline trend. For continuous gas lifted wells, several attempts have been made to model production rates, but none have been found to be simple or accurate. In this article the principle of superposition has been applied such that the production rate of a well at a time, t after gas-lift has been introduced would be the sum of the flow rate due to the natural flow and gas-lift induced flow rate. Four actual well production data sets obtained from the SPE Data Repository and from reservoirs in literature from Niger Delta were used to assess the model. The analysis done included cases with and without gas lift and statistical analysis was done to evaluate the error margin. The equation derived is a mathematical model in which the traditional Arps’ exponential model accounts for the natural flow and a power law model accounts for the gas-lift induced flow expressed as:
q_t=q_inf 〖[e〗^(-Dt)+βt^(-λD)]
The model proposed showed that 0.48MMstb, 0.31MMstb, 8.75MMstb, and 1.23MMstb respectively would be produced when gas-lift is introduced as opposed to 0.26MMstb, 0.16MMstb, 7.96MMstb, and 1.10MMstb without gas-lift respectively, from well 1 to 4. The model also predicted future rates that were similar to the actual field data with correlation coefficient of 0.884, 0.806, 0.917, and 0.874 respectively. This statistical result indicates the effectiveness of the model in predicting the production decline rate of gas-lifted wells.
- References
- Downloads
- Published
- 29-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Ayodele DANIEL, Mercy O. AKEJU, Sunday O. ISEHUNWA, Abel A. ADEYI, Adebayo T. OGUNYEMI (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Shehu ABDULKADIR, Dangora N. DAUDA, Aliyu A. ADAMU, Badaru M. SANI, Rilwan ABUBAKAR, Timothy A. TIMOTHY, Uchechukwu M. AGBOM, Abubakar S. ABUBAKAR, Development and Performance Evaluation of a Modified Active Evaporative Cooling System for Postharvest Preservation of Selected Vegetables , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bosede A. ORHEVBA, Sodeeq A. OLAJIDE, Optimization of Alkaline Pretreatment and Fermentation Conditions for Improved Physicochemical Properties and Yield of Bioethanol Produced from Sugarcane Bagasse , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Obafemi A. IBITOYE, Jemimah O. TOLU-ALALADE, Solar-Powered Low-Cost Housing: Designing Off-Grid Communities with Interlocking Stabilised Soil Blocks (ISSB) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Paul A. OMALE, Hammed O. SALAUDEEN, Sunday S. IGILA, Enoch T. CHIN, Determination of the Physicochemical Composition of Processed Powdered Pepper (Capsicum spp.) Sold in Selected Markets in Makurdi, Benue State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Chinemeogo C. OZIOKO, Ikechukwu C.-E. IKE-EZE, Nnanyelugo O. EDWIN, Dimelu K. EBUBE, Charles MBOHWA, Investigation of the Mechanical and Thermal Properties of Waste Toner Powder Reinforced Polyester Composite for Industrial Applications , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Afeez A. AWOLOKUN, Olusegun O. ALUKO, Temitope F. AWOLUSI, Mayowa A. OGIDI, Performance Evaluation of Pervious Concrete Containing Glass Cullet and Glass Powder for Sustainable Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kayode A. IDOWU, Victory N. JESSEY, Emmanuel B. SAMANI, The Role of Aesthetic Properties of Granitic Dimension Stones on Marketability: A Case Study of CIBI Nigeria Limited, Kaduna State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar HASSAN, Emmanuel G. DADA, Comparative Analysis of Machine Learning Classifiers for E-mail Spam Filtering with RFE-SVM Feature Selection and SA-Optimised XGBoost , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Oluwayinka. G. AKINWAMIDE, Olugbenga O. AMU, Christopher FAPOHUNDA, Prediction of International Roughness Index of Flexible Pavement Using Machine Learning-Based Predictive Framework in Ekiti State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Enoch ADETONA, Oladiran K. ABUBAKRE, Rasheed A. MURIANA, Muhammad N. BALA, Abel A. ADEYI, Evaluation of Animal Dungs as Alternative Heat-Treating Materials in Foundry Shop , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Stephen G. UDEAGBARA, Judith A. KAINE, Ayodele DANIEL, Ifeanyi A. OGUAMAH, Performance Evaluation of an Additive in Formic Acid Blend for Well Stimulation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
