Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA
- Authors
-
-
Mela I. L. LASHIRU
Author
-
Ganiyu A. BAKARE
Author
-
Sabo M. HASSAN
Author
-
Kamilu O. LAWAL
Author
-
- Keywords:
- Active Distribution Network, D-PMU, Observability, Data-Driven Control, APSO, ASDA, Distribution System State Estimation, Rate-of-Change of Frequency ROCOF.
- Abstract
-
The increasing deployment of renewable Distributed Generators (DGs) introduces operational uncertainty and observability challenges in Active Distribution Networks (ADNs). Traditional Supervisory Control and Data Acquisition (SCADA) systems lack the temporal resolution required for real-time monitoring. This paper proposes a data-driven framework for enhancing network observability through optimal co-deployment of DGs and Distribution Phasor Measurement Units (D-PMUs) using a hybrid Accelerated Particle Swarm Optimization-Adaptive Spiral Dynamic Algorithm (APSO-ASDA). The objective is to maximize network observability with minimal measurement redundancy for improved Distribution System State Estimation (DSSE). Simulation results on the IEEE 13-bus ADN, modeled in MATLAB Simulink R2023b, showed ASDA optimal DG -D-PMU placement at buses 1, 4, with corresponding sizes of 340Kw(solar), and 445kW(wind) with D-PMU at 6, 7, 10, and 12. APSO DG placement is at bus 3 and 4 with a size of 60kW(solar), 400kW(wind), D-PMU at buses 6, 8, 9. The hybrid approach places DG at buses 1 and 3 with corresponding capacities of 110kW (solar) and 250kW (wind), and D-PMU allocation at buses 4, 6, 7, 8, 11 and 12. The hybrid algorithm achieved a rapid reduction in the cost function from 278.7 to 81.14 within the first 36 iterations, highlighting its effectiveness for real-time, data-driven applications.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Olarewaju T. OGINNI, An Overview of Unmanned Aerial Vehicles Technologies for Office Use and Services Delivery , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abdulrahman S. USMAN, Folorunsho ABERUAGBA, Moses A. OLUTOYE, Umar MUSA, Mohammed ALHASSAN, Calcium Oxide Derived from Okpella Limestone as a Heterogeneous Catalyst for Biodiesel Production: Synthesis, Characterisation and Stability Assessment , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Usman A. ALI, Munir A. ADEWOYE, Adamu U. ABDULLAHI, Determinants of Blockchain Adoption for Academic Certificate Verification: Insights from Verification Officers for Sustainable Education in Nigerian Higher Education Institutions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Lawal B. IDRIS, A Review on Vehicular Ad Hoc Network (VANET) Security challenges and Solutions , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ibrahim BALA, Solomon M. DAUDA, Audu A. BALAMI, Peter A. IDAH, Design Analysis of a Kenaf Decorticating Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bala YAHAYA, Mukhtar N. YAHYA, Characterization of Soil Properties Under Continuous Irrigation Practice , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Samaila J. EL-PATEH, Ibrahim IDRIS, Waste Management in Bauchi Metropolis: Solid Measure and Characterization in Municipality , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adekunle O. ADEWOLE, Ayodeji O. ARIYO, Development of an Edge-Enabled IoT Smart Energy Meter with Artificial Intelligence (AI)-Based Load Prediction for Device-Level Monitoring , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adefemi O. ADEODU, Banjo C. ADEDOKUN, Amos A. ADEGBITE, Development and Performance Evaluation of an Injection Moulding Machine for Recycled Polymer Composite Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Adesoye S. ADEGOKE, Lateef A. OTEGBEYE, Olufemi S. SONEYE, Oluwole O. GREEN, Patrick O. OLABISI, Assessment of Radio-Frequency Radiation Levels from Cellular Base Transceiver Stations in Residential Areas and Their Potential Health Effects on Humans , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Umar A. ADAMU, Ya’u S. HARUNA, Ganiyu A. BAKARE, Buhari H. MAMMAN, Kunduli MUSTAPHA, Hadi M. ADAMU, Ismaila MAHMUD, Design and Simulation of a 200 MWp Floating Solar PV Plant Integrated with the Kainji Hydropower Plant, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
