BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions
- Authors
-
-
Emmanuel T. ODEYEMI
Author
-
Ya’u S. HARUNA
Author
-
Ganiyu A. BAKARE
Author
-
Hassan B. MAMMAN
Author
-
Sabo M. HASSAN
Author
-
- Keywords:
- Permanent Magnet Synchronous Generator, Maximum Power Point Tracking, Adaptive Neuro-Fuzzy Inference System, Wind Energy Conversion System, and Wind Speed.
- Abstract
-
Efficient maximum power point tracking (MPPT) in variable-speed wind energy conversion systems (WECS) is challenged by nonlinear turbine–generator dynamics and rapidly varying wind conditions, which limit the effectiveness of conventional controllers. This paper proposes an intelligent torque-based MPPT framework for a 0.5 MW grid-connected permanent magnet synchronous generator (PMSG) WECS, combining metaheuristic optimization with adaptive neuro-fuzzy control. A high-fidelity MATLAB/Simulink model integrating turbine aerodynamics, generator dynamics, and power electronic conversion is developed for systematic evaluation. Three controllers; conventional PID, BAT-optimized PID (BAT-PID), and BAT-optimized adaptive neuro-fuzzy inference system (BAT-ANFIS), are comparatively assessed under step, ramp, and turbulent wind profiles. Results show that BAT optimization improves PID transient performance by 25–30% and reduces steady-state error to 5.2%. The proposed BAT-ANFIS further achieves a 40–45% reduction in settling time relative to conventional PID and a 15–20% improvement over BAT-PID, while maintaining DC-link voltage within ±1% of nominal (950–970 V). Torque ripple is reduced by ~30%, and MPPT efficiency reaches 100% under ramp conditions and ≈98% under turbulent profiles, outperforming BAT-PID (≈86–96%) and conventional PID (≈78–88%). These results demonstrate that integrating BAT-based optimization with neuro-fuzzy adaptation significantly enhances dynamic response, robustness, and real-time power extraction, establishing BAT-ANFIS as a high-performance MPPT solution for large-scale wind energy systems.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Kayode A. IDOWU, Victory N. JESSEY, Emmanuel B. SAMANI, The Role of Aesthetic Properties of Granitic Dimension Stones on Marketability: A Case Study of CIBI Nigeria Limited, Kaduna State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Joshua T. AKINWAMIDE, Jacob O. EHIOROBO, Oluwayinka G. AKINWAMIDE, Geotechnical Evaluation of Lateritic Soil Index Properties in Ekiti State Districts, Southwestern Nigeria for Road Pavement Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Munir A. ADEWOYE, Ahmed ALIYU, Usman A. ALI, Abdulrasheed JIMOH, Blockchain-Based Food Supply Chain Traceability: A Systematic Review of Privacy Preserving and Scalability , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Cyril OCHERI, Victor S. AIGBODION, Esther O. AMEH, Ihebuchuwu C. EZEAKU, Chibuikem A. OKAFOR, Uchenna C. AMAZUE, Eddy R. OMONIGHO, Electrochemical Analysis of Azadirachta indica Leaves as a Corrosion inhibitor on Mild Steel in 1 M H2SO4 , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Kazeem A. BELLO, Adeniyi O. ADESINA, Lukman A. OPEYEMI, Solomon O. UVIASE, Francis O. BOROKINNI, Friday ONUH, Tunde O. OGUNDANA, Adebayo I. OLUMOROTI, Developments and Applications of Additive Manufacturing in the Automotive Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Benjamin BELLO, Jibril D. JIYA, Aje TOKAN, Ahmed MOHAMMED, Classification of Groundnut Pod Varieties using Histogram-Based Gradient Booster Classifier (HGBC) with Machine Learning Techniques , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chukwuemeka S. IBEH, Abubakre O. KAMARDEEN, Saka A. ABDULKAREEM, Aliyu A. ABDULLAHI, Experimental Study on the Characterisation and Thermo-Physical Properties of Graphene-Agro Based Hybrid Nanofluids , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kamoru O. OLADOSU, Kabiru MUSTAPHA, Ayodeji S. OLAWORE, Akeem B. IBRAHIM, Abdulganiyu ISSA, Development of a Free-Fall Pyrolysis Reactor for Biofuel Production Using Sugarcane Bagasse and Cassava Rhizomes as Feedstocks , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mohammed U. GARBA, Musa A. ABDULLAHI, Isah RABI, Saadatu A. GORO, Habibu UTHMAN, Abubakar S. MOHAMMED, Umaru AHMADU, Usman S. ONODUKU, Recovery of Lithium Carbonate from Nigerian Lepidolite Ore via Roasting-Leaching-Precipitation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
