BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions
- Authors
-
-
Emmanuel T. ODEYEMI
Author
-
Ya’u S. HARUNA
Author
-
Ganiyu A. BAKARE
Author
-
Hassan B. MAMMAN
Author
-
Sabo M. HASSAN
Author
-
- Keywords:
- Permanent Magnet Synchronous Generator, Maximum Power Point Tracking, Adaptive Neuro-Fuzzy Inference System, Wind Energy Conversion System, and Wind Speed.
- Abstract
-
Efficient maximum power point tracking (MPPT) in variable-speed wind energy conversion systems (WECS) is challenged by nonlinear turbine–generator dynamics and rapidly varying wind conditions, which limit the effectiveness of conventional controllers. This paper proposes an intelligent torque-based MPPT framework for a 0.5 MW grid-connected permanent magnet synchronous generator (PMSG) WECS, combining metaheuristic optimization with adaptive neuro-fuzzy control. A high-fidelity MATLAB/Simulink model integrating turbine aerodynamics, generator dynamics, and power electronic conversion is developed for systematic evaluation. Three controllers; conventional PID, BAT-optimized PID (BAT-PID), and BAT-optimized adaptive neuro-fuzzy inference system (BAT-ANFIS), are comparatively assessed under step, ramp, and turbulent wind profiles. Results show that BAT optimization improves PID transient performance by 25–30% and reduces steady-state error to 5.2%. The proposed BAT-ANFIS further achieves a 40–45% reduction in settling time relative to conventional PID and a 15–20% improvement over BAT-PID, while maintaining DC-link voltage within ±1% of nominal (950–970 V). Torque ripple is reduced by ~30%, and MPPT efficiency reaches 100% under ramp conditions and ≈98% under turbulent profiles, outperforming BAT-PID (≈86–96%) and conventional PID (≈78–88%). These results demonstrate that integrating BAT-based optimization with neuro-fuzzy adaptation significantly enhances dynamic response, robustness, and real-time power extraction, establishing BAT-ANFIS as a high-performance MPPT solution for large-scale wind energy systems.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Tahiru MOHAMMED, Muhammad B. MAINA, Abba B. MUHAMMAD, Muhammad SHUWA, From Local Sand to Functional Silicon: An Integrated Pathway for Producing Photovoltaic-Grade Material from Nigerian Silica Sand , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bala I. ABDULKARIM, Umar IDRISS, Synthesis and Characterization of Laggera aurita-Derived KOH Activated Carbon (LAKOHAC) and Role for the Adsorption of Water-Soluble Fraction of Benzene (WSFB) in Oil-Spilled Water , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Murtala NAMAKKA, Abdulhamid S. ILIYASU, Utilisation of Supercritical Critical Fluids in Adsorption Process: A Comprehensive Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- James AUDU, Abdulraman A. SALAWU, Muriana R. AREMU, Abdullahi A. ALHAJI, Lawal S. SIUS, Characterisation of Pumice-Kaolin Refractory Bricks for High Temperature Industrial Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Shehu S. SHEHU, Samuel O. OLADIPUPO, Dominic S. NYITAMEN, Simulation and Performance Analysis of a Military Insignia Microstrip Patch Antenna at 2.45 GHz For Wireless Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Vincent B. ONIGBARA, Muftau A. GBENLE, Sunday I. AGU, Mechanical and Biological Performance of Titanium Hydroxyapatite Composites for Biomedical Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Jamesmary E. AYANRU, Matthew S. ABOLARIN, Omotayo I. OGUNWEDE, Henry I. MORKAH, Adeshola O. OPENIBO, Development and Performance Evaluation of a Dryer for Preserving Vegetable Leaves , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adekunle A. YEKINNI, Adeniyi O. ADESINA, Kazeem A. BELLO, Effect of Subcritical Tempering on the Microstructural, Mechanical and Corrosion Behaviour of Mild Steel , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abdulkareem BELLO, Yusuf O. ADEIZA, Saleh S. LUKMAN, Muhammad A. ADAMU, Chibuzor A. OKAFOR, Abdulaziz A. ABDULSALAM, Production of Silica from ABU Zaria Dam Sand as an Eco-Friendly Corrosion Inhibitor Using Nanotechnology , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Israel A. OLUWAFEMI, Akaninyene B. OBOT, Emmanuel UBOM, Ayodele A. OLATUNJI, Mbuotidem G. ROBINSON, Design and Analysis of a Dual-Band Circular Microstrip Antenna Using Spatially Distributed CSRRs , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Umar A. ADAMU, Ya’u S. HARUNA, Ganiyu A. BAKARE, Buhari H. MAMMAN, Kunduli MUSTAPHA, Hadi M. ADAMU, Ismaila MAHMUD, Design and Simulation of a 200 MWp Floating Solar PV Plant Integrated with the Kainji Hydropower Plant, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
