Experimental Investigation of Solar Photovoltaic Tilt Angles for Maximum Energy Harvest in Kogi State, Nigeria
- Authors
-
-
Habib I. ABDULAZEEZ
Rural Electrification Agency (REA), Abuja, Nigeria
Author
-
Bala ABDULLAHI
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology, Wudil, Kano State, Nigeria
Author
-
Abdullahi AHMED
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology Wudil, Kano State, Nigeria
Author
-
Ibrahim A. TUKUR
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology, Wudil, Kano State, Nigeria
Author
-
- Keywords:
- Solar photovoltaic (PV) panels, tilt angle optimization, solar radiation, Kogi State, Nigeria.
- Abstract
-
This study aimed to investigate the impact of tilt angles on solar radiation, current, voltage, and power output of a photovoltaic system, while also employing mathematical modeling to predict solar radiation. This study experimentally investigates the effect of tilt angle (0°, 7.8°, 22.8°, 37.8°, and 52.8°) on the performance of 10W polycrystalline solar panels in Kogi State, Nigeria, over a 12-month period (November 2023–October 2024). Solar radiation, current, and power output were measured at 20-minute intervals using data loggers, voltmeters, and ammeters. The study only investigates the effect of tilt angle and does not consider other factors that may impact solar panel efficiency, such as dust accumulation, temperature, or shading. Results show that optimal performance varies seasonally: lower angles (0°–7.8°) yielded higher radiation and power during peak dry seasons (e.g., November, 613.67 W/m² at 22.8°), while steeper angles (22.8°–37.8°) performed better in transitional months. The 7.8° tilt achieved the highest yearly average radiation, whereas the 0° tilt produced the highest average current (0.300 A) and power (4.51 W). These findings suggest that adjusting tilt angles seasonally can maximize solar energy efficiency in Kogi State, with 7.8° recommended as the best annual fixed tilt.
- References
- Downloads
- Published
- 08-08-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Hillary T. OGBODO, Bilkisu L. MUHAMMAD-BELLO, Joshua ABAH, Saleh E.-Y. ABDULLAHI, Quantum Computing Applications in Software Engineering: A Scoping Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bosede A. ORHEVBA, Sodeeq A. OLAJIDE, Optimization of Alkaline Pretreatment and Fermentation Conditions for Improved Physicochemical Properties and Yield of Bioethanol Produced from Sugarcane Bagasse , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Abba M. BALA, Abdurrauf G. SHARIFAI, Umar S. HARUNA, A Hybrid Deep Learning Model for Efficient Anomaly Detection in Video Surveillance Systems , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abimbola J. KOLAWOLE, AbdulKodri G. ABDULRAFIU, An Evaluation of the Challenges and Limitations in the Adoption of Technological Innovations at Nnamdi Azikiwe International Airport , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Auwalu M. ABDULLAHI, Musa M. BELLO, Ado HARUNA, Amina I. KHALEEL, Lubabatu B. ILA, Abdurrahaman M. BELLO, Adaptive Hybrid Compliant Control of a Desktop Upper-Limb Rehabilitation Robot , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Samuel O. OLADIPUPO, Dominic S. NYITAMEN, Lanre S. MOJEREOLA, Design, Simulation and Fabrication of a Slot Loaded 2.45 GHz Microstrip Patch Antenna for ISM Band Wireless Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nnamdi S. OKOMBA, Adedayo A. SOBOWALE, Adebimpe O. ESAN, Bolaji A. OMODUNBI, Taiwo A. AWOYEMI, Development of an Intelligent-Based Elevator System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mohammed A. GANA, Zaka A. MSHELIA, Isuwa S. AJI, Alhaji GUJJA, Lawan A.M. KOLO, Investigation and Comparative Analysis of Natural Moulding Sands from Five Deposits in Maiduguri, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sulaiman Y. ADAMU, Fadimatu N. DABAI, Abdulazeez Y. ATTA, Baba Y. JIBRIL, Preparation and Characterization of Enhanced Hierarchical Zn-Ni/HZSM-5 Catalysts for Potential use in Catalytic reactions to Upgrade Bio-Oil and Hydrogen from Biomass Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
