Development of Coconut Shell Hydrochar for Lead Removal from Pharmaceutical Wastewater
- Authors
-
-
Adegoke P. ADEBOLA
Author
-
Abubakar S. MOHAMMED
Author
-
Umaru MUSA
Author
-
Abubakar A. IBRAHIM
Author
-
Abubakar G. ISAH
Author
-
Mohammed U. GARBA
Author
-
- Keywords:
- Coconut shell hydrochar; Hydrothermal carbonization; Pb²⁺ adsorption; Pharmaceutical wastewater; Heavy-metal removal.
- Abstract
-
Lead (Pb²⁺) contamination of wastewater requires effective, low-cost, and sustainable treatment materials. This study investigated coconut shell hydrochar produced by hydrothermal carbonization (HTC) for Pb²⁺ removal from aqueous solution and pharmaceutical wastewater. Coconut shells were converted to hydrochar at 200, 220, and 240 °C and characterized using proximate, Fourier transform infrared spectroscopy – FTIR, ultimate analysis and BET surface area. The hydrochar produced at 240 °C exhibited a specific surface area of 560.45 m²/g and was selected for adsorption experiments. Batch adsorption studies evaluated the effects of pH, contact time, dosage concentration, temperature, and initial Pb²⁺ concentration. Adsorption equilibrium, kinetics, and thermodynamics were assessed using Langmuir, Freundlich, pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. Pb²⁺ removal increased if contact time and adsorbent dosage increases reaching 99.19% at 120 min and 99.46% at 2.0 g/L, respectively. Increasing initial Pb²⁺ concentration increased adsorption capacity from 0.01665 to 0.180 mg/g but reduced percentage removal. The Freundlich model provided the best equilibrium fit (R² = 0.9996), while the Langmuir model gave R² = 0.9374 and a maximum adsorption capacity of 0.2502 mg/g. The pseudo-second-order model best fit the adsorption kinetics (R² = 0.955). Thermodynamic analysis indicated spontaneous and endothermic adsorption, with negative ΔG values (−0.708 to −2.443 kJ/mol), ΔH of 25.15 kJ/mol, and ΔS of 86.72 J/mol·K. Overall, coconut shell hydrochar showed promising potential for sustainable Pb²⁺ removal from wastewater.
- References
- Downloads
- Published
- 09-10-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Adegoke P. ADEBOLA, Abubakar S. MOHAMMED, Umaru MUSA, Abubakar A. IBRAHIM, Abubakar G. ISAH, Mohammed U. GARBA (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Mohammed B. ABDULLAHI, Impact of Agro-Chemicals on Groundwater Quality and Soils of Irrigation Sites: A Case Study of Chanchaga Irrigation Scheme, Minna, Niger State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mercy S. OMEIFE, Toyin Y. AKANBI, Peace D. PAUL, Mechanical Characterization of Concrete Reinforced with Sisal Fibers and Expanded Polystyrene Aggregates , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abubakar S. MOHAMMED, Mohammed ALIYU, Mohammed U. GARBA, Ibrahim S. MOHAMMED, Ibrahim A. KUTI, Meshack S. IMOLOGIE, Umaru MUSA, Olalekan D. ADENIYI, Peter A. ADEOYE, Abubakar G. ISAH, Folarin T. OLORUNMOTITO, Development and Packaging of Eco-friendly Biosolid Briquettes Synthesised with Bagasse for Green Energy Generation and Utilisation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Zachariah S. PYENDANG, Felix ACHEMA, Isheni YAKUBU, Solomon E. APEH, Microstructural Characterization of Fibre Reinforced Polymer (FRP) Composite (Kenaf Fibre and Polyester Resin) for Structural Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bala YAHAYA, Characterization of Soil Quality Parameters in Sector 2 of Watari Irrigation Project, Kano , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abubakar M. ALI, Haruna IBRAHIM, Ephraim G. KEFAS, Thermal Plasma Gasification of Municipal Solid Waste: Principles, Technological Advances, Challenges, and Future Prospects , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abubakar A. IBRAHIM, Fatimah Y. GARBA, Fatimah A. MUHAMMAD, Ismail B. ADEFESO, Bello A. ISAH, Jacob OLAYIWOLA, Industrial and Biomedical Applications Biobased Polymers of Polylactic Acid and Polyhydroxybutyrate: A Review , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adegboyega L. ALUKO, Ayodeji T. BALOGUN, Environmental Impact of Gold Mining Activities and Sustainable Mitigation Approaches: Case Study of Ilesa Surrounding areas, Osun State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kazeem A. BELLO, Adeniyi O. ADESINA, Lukman A. OPEYEMI, Solomon O. UVIASE, Francis O. BOROKINNI, Friday ONUH, Tunde O. OGUNDANA, Adebayo I. OLUMOROTI, Developments and Applications of Additive Manufacturing in the Automotive Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abdulkarim AMINU, Mohammed ALIYU, Ibrahim S. MOHAMMED, Iyanda M. ANIMASHAUN, Peter DANIEL, Mohammad USMAN, Production and Optimisation of Parameters for Density and Ash Content of Briquettes Produced from Sorghum Stalks and Groundnut Shells Using African Locust Bean (Parkia biglobosa) Pulp as a Binding Agent , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Iyanda M. ANIMASHAUN, Abubakar S. MOHAMMED, Ibrahim A. KUTI, Peter A. OBASA, Rashidat ANIYIKAYE, Yahaya MOHAMMED, Yusuf M. OTACHE, Artificial Intelligence of Things (AIoT) for Precision Irrigation: A Comprehensive Review of Applications, Challenges, and Future Directions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Muhammad N. IBRAHIM, Abubakar S. MOHAMMED, Iyanda M. ANIMASHAUN, Shehu ABDULKADIR, Sensor-Based Real-Time Soil Macronutrient Monitoring and Variable-Rate Fertilizer Application Machinery , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
