Development of Coconut Shell Hydrochar for Lead Removal from Pharmaceutical Wastewater
- Authors
-
-
Adegoke P. ADEBOLA
Author
-
Abubakar S. MOHAMMED
Author
-
Umaru MUSA
Author
-
Abubakar A. IBRAHIM
Author
-
Abubakar G. ISAH
Author
-
Mohammed U. GARBA
Author
-
- Keywords:
- Coconut shell hydrochar; Hydrothermal carbonization; Pb²⁺ adsorption; Pharmaceutical wastewater; Heavy-metal removal.
- Abstract
-
Lead (Pb²⁺) contamination of wastewater requires effective, low-cost, and sustainable treatment materials. This study investigated coconut shell hydrochar produced by hydrothermal carbonization (HTC) for Pb²⁺ removal from aqueous solution and pharmaceutical wastewater. Coconut shells were converted to hydrochar at 200, 220, and 240 °C and characterized using proximate, Fourier transform infrared spectroscopy – FTIR, ultimate analysis and BET surface area. The hydrochar produced at 240 °C exhibited a specific surface area of 560.45 m²/g and was selected for adsorption experiments. Batch adsorption studies evaluated the effects of pH, contact time, dosage concentration, temperature, and initial Pb²⁺ concentration. Adsorption equilibrium, kinetics, and thermodynamics were assessed using Langmuir, Freundlich, pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. Pb²⁺ removal increased if contact time and adsorbent dosage increases reaching 99.19% at 120 min and 99.46% at 2.0 g/L, respectively. Increasing initial Pb²⁺ concentration increased adsorption capacity from 0.01665 to 0.180 mg/g but reduced percentage removal. The Freundlich model provided the best equilibrium fit (R² = 0.9996), while the Langmuir model gave R² = 0.9374 and a maximum adsorption capacity of 0.2502 mg/g. The pseudo-second-order model best fit the adsorption kinetics (R² = 0.955). Thermodynamic analysis indicated spontaneous and endothermic adsorption, with negative ΔG values (−0.708 to −2.443 kJ/mol), ΔH of 25.15 kJ/mol, and ΔS of 86.72 J/mol·K. Overall, coconut shell hydrochar showed promising potential for sustainable Pb²⁺ removal from wastewater.
- References
- Downloads
- Published
- 09-10-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Adegoke P. ADEBOLA, Abubakar S. MOHAMMED, Umaru MUSA, Abubakar A. IBRAHIM, Abubakar G. ISAH, Mohammed U. GARBA (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Stephen YAKUBU, Baba MAKUN, Effect of Petroleum Contamination on Soil Properties and the Removal Efficiency of Volatile Organic Compounds Using Air-Stripping System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bala I. ABDULKARIM, Phebe O. JAMES, Utilization of Microbial Fuel Cells for Electricity Generation from Gwagwalada Abattoir Wastewater , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Victoria A. UMEJURU, Isaac E. IHUA-MADUENYI, Adaobi S. NWOSI-ANELE, Performance Evaluation and Economic Assessment of Electrical Submersible Pumps for Heavy Oil Production in Mature Niger Delta Oilfields , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Oguntola J. ALAMU, Peter O. ILORI, Seun OYELAMI, Wasiu O. ADEDEJI, Tunji J. ADEPOJU, Abideen T. OYEWO, A Review of the Effect of Post-Processing Heat Treatment on 3D Printed Metal Parts , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Chioma I. MADUEKE, Reginald UMUNAKWE, Oluwole D. ADIGUN, An Evaluation of the Porosity and Pore Volume Fractions of Coir Fibres in Relation to Their Diameters and Tensile Properties at a Crosshead Displacement Rate of 0.5 mm/Minute for Composite Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Ndagi MAMUDU, Ibrahim S. MOHAMMED, Mohammed ALIYU, Peter DANIEL, Timothy Y. AKANDE, Bala A. GARBA, Development and Performance Evaluation of Biomass Pyrolysis System for Biofuel Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sarafa ISHOLA, Olusegun S. OLAOYE, Adeyinka A. ADEGBOLA, Isaac A. OLUREMI, Oluseye O. AGBEDE, Drying Kinetics and Combustion Characteristics of Carbonized Cashew Nut Shell Briquettes Under Open Sun, Passive and Active Solar Drying , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Isaac O. OLAOYE, Design Modification and Performance Evaluation of an Existing Cashew Nut Shell Liquid (CNSL) Extraction Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Cyril OCHERI, Victor S. AIGBODION, Esther O. AMEH, Ihebuchuwu C. EZEAKU, Chibuikem A. OKAFOR, Uchenna C. AMAZUE, Eddy R. OMONIGHO, Electrochemical Analysis of Azadirachta indica Leaves as a Corrosion inhibitor on Mild Steel in 1 M H2SO4 , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Iyanda M. ANIMASHAUN, Abubakar S. MOHAMMED, Ibrahim A. KUTI, Peter A. OBASA, Rashidat ANIYIKAYE, Yahaya MOHAMMED, Yusuf M. OTACHE, Artificial Intelligence of Things (AIoT) for Precision Irrigation: A Comprehensive Review of Applications, Challenges, and Future Directions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Muhammad N. IBRAHIM, Abubakar S. MOHAMMED, Iyanda M. ANIMASHAUN, Shehu ABDULKADIR, Sensor-Based Real-Time Soil Macronutrient Monitoring and Variable-Rate Fertilizer Application Machinery , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
