Decline Curve Analysis of Continuous Injection Gas Lifted Wells
- Authors
-
-
Ayodele DANIEL
Author
-
Mercy O. AKEJU
Author
-
Sunday O. ISEHUNWA
Author
-
Abel A. ADEYI
Author
-
Adebayo T. OGUNYEMI
Author
-
- Keywords:
- Decline curve analysis, Developed reserves, Production rate, Gas lift, Arps’ exponential model.
- Abstract
-
Decline Curve Analysis is one of the established techniques for reservoir performance evaluation and estimation of developed reserves. While it has been well utilized for natural drive production, there have been challenges in accurate evaluation of gas lifted wells because of additional energy that supplements the natural which changes future production rate of the reservoir and distorts the reservoir’s production decline trend. For continuous gas lifted wells, several attempts have been made to model production rates, but none have been found to be simple or accurate. In this article the principle of superposition has been applied such that the production rate of a well at a time, t after gas-lift has been introduced would be the sum of the flow rate due to the natural flow and gas-lift induced flow rate. Four actual well production data sets obtained from the SPE Data Repository and from reservoirs in literature from Niger Delta were used to assess the model. The analysis done included cases with and without gas lift and statistical analysis was done to evaluate the error margin. The equation derived is a mathematical model in which the traditional Arps’ exponential model accounts for the natural flow and a power law model accounts for the gas-lift induced flow expressed as:
q_t=q_inf 〖[e〗^(-Dt)+βt^(-λD)]
The model proposed showed that 0.48MMstb, 0.31MMstb, 8.75MMstb, and 1.23MMstb respectively would be produced when gas-lift is introduced as opposed to 0.26MMstb, 0.16MMstb, 7.96MMstb, and 1.10MMstb without gas-lift respectively, from well 1 to 4. The model also predicted future rates that were similar to the actual field data with correlation coefficient of 0.884, 0.806, 0.917, and 0.874 respectively. This statistical result indicates the effectiveness of the model in predicting the production decline rate of gas-lifted wells.
- References
- Downloads
- Published
- 29-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Ayodele DANIEL, Mercy O. AKEJU, Sunday O. ISEHUNWA, Abel A. ADEYI, Adebayo T. OGUNYEMI (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Ameh RICHARD, Sani B. MUHAMMAD, Terver AUSE, Umar SHEHU, Assessment of the Suitability of Wusasa Clay for Refractory Bricks Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Usman A. ABDURRAHMAN, Abubakar A. ROGO, Abdulkadir A. BICHI, Akibu M. ABDULLAHI, Beyond Overload: Assessing Cognitive Load to Facilitate Learning Transfer in Virtual Environments , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ahmad ADO, Abdullahi YAHAYA, Abubakar J. MUHAMMAD, Zaharaddeen G. SANI, Baba A. OLUWA, Abdulazeez A. YUSUF, Kinetic Study of 4-Nitrophenol Sonocatalytic Degradation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abdulkareem BELLO, Yusuf O. ADEIZA, Saleh S. LUKMAN, Muhammad A. ADAMU, Chibuzor A. OKAFOR, Abdulaziz A. ABDULSALAM, Production of Silica from ABU Zaria Dam Sand as an Eco-Friendly Corrosion Inhibitor Using Nanotechnology , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olatunde A. AKANO, Wariz A. ISMAEL, Ayomikun A. AWOSEYI, Femi AYO, Ifeoluwa M. OLANIYI, Jide E.T. AKINSOLA, Short Messaging Service Spam Detection Model Using Natural Language Processing and Deep Learning Techniques , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Nuhu MOHAMMED, Garkuwa Y. ADAMU, Abubakar A. FACHWAY, Aminu MOHAMMED, Afolayan A. OLASUNKANMI, Odoh F. CHIMEZIE, Muhammad A. YUSUF, Development of A Water-Recycling Pico Hydropower System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adekunle O. ADEWOLE, Ayodeji O. ARIYO, Development of an Edge-Enabled IoT Smart Energy Meter with Artificial Intelligence (AI)-Based Load Prediction for Device-Level Monitoring , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sati C. NSHOL, Saeed Y. UMAR, Suleiman A. YERO, Modification of the Engineering Properties of Road Base Course Soil Materials with Cement and Polyethylene Terephthalate (PET) , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mohammed B. ABDULLAHI, Impact of Agro-Chemicals on Groundwater Quality and Soils of Irrigation Sites: A Case Study of Chanchaga Irrigation Scheme, Minna, Niger State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sulaiman Y. ADAMU, Fadimatu N. DABAI, Abdulazeez Y. ATTA, Baba Y. JIBRIL, Preparation and Characterization of Enhanced Hierarchical Zn-Ni/HZSM-5 Catalysts for Potential use in Catalytic reactions to Upgrade Bio-Oil and Hydrogen from Biomass Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Enoch ADETONA, Oladiran K. ABUBAKRE, Rasheed A. MURIANA, Muhammad N. BALA, Abel A. ADEYI, Evaluation of Animal Dungs as Alternative Heat-Treating Materials in Foundry Shop , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
