Decline Curve Analysis of Continuous Injection Gas Lifted Wells
- Authors
-
-
Ayodele DANIEL
Author
-
Mercy O. AKEJU
Author
-
Sunday O. ISEHUNWA
Author
-
Abel A. ADEYI
Author
-
Adebayo T. OGUNYEMI
Author
-
- Keywords:
- Decline curve analysis, Developed reserves, Production rate, Gas lift, Arps’ exponential model.
- Abstract
-
Decline Curve Analysis is one of the established techniques for reservoir performance evaluation and estimation of developed reserves. While it has been well utilized for natural drive production, there have been challenges in accurate evaluation of gas lifted wells because of additional energy that supplements the natural which changes future production rate of the reservoir and distorts the reservoir’s production decline trend. For continuous gas lifted wells, several attempts have been made to model production rates, but none have been found to be simple or accurate. In this article the principle of superposition has been applied such that the production rate of a well at a time, t after gas-lift has been introduced would be the sum of the flow rate due to the natural flow and gas-lift induced flow rate. Four actual well production data sets obtained from the SPE Data Repository and from reservoirs in literature from Niger Delta were used to assess the model. The analysis done included cases with and without gas lift and statistical analysis was done to evaluate the error margin. The equation derived is a mathematical model in which the traditional Arps’ exponential model accounts for the natural flow and a power law model accounts for the gas-lift induced flow expressed as:
q_t=q_inf 〖[e〗^(-Dt)+βt^(-λD)]
The model proposed showed that 0.48MMstb, 0.31MMstb, 8.75MMstb, and 1.23MMstb respectively would be produced when gas-lift is introduced as opposed to 0.26MMstb, 0.16MMstb, 7.96MMstb, and 1.10MMstb without gas-lift respectively, from well 1 to 4. The model also predicted future rates that were similar to the actual field data with correlation coefficient of 0.884, 0.806, 0.917, and 0.874 respectively. This statistical result indicates the effectiveness of the model in predicting the production decline rate of gas-lifted wells.
- References
- Downloads
- Published
- 29-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Ayodele DANIEL, Mercy O. AKEJU, Sunday O. ISEHUNWA, Abel A. ADEYI, Adebayo T. OGUNYEMI (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Oluwasanmi S. ADANIGBO, Opeyemi O. ASAOLU, Adedayo A. SOBOWALE, Temidayo AKINDAHUNSI, Akinbayode A. ASAOLU, Intrusion Detection in Mobile Adhoc Networks: A Review of Signature-Based, Anomaly-Based, and Hybrid Approaches , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Joshua T. AKINWAMIDE, Jacob O. EHIOROBO, Oluwayinka G. AKINWAMIDE, Geotechnical Evaluation of Lateritic Soil Index Properties in Ekiti State Districts, Southwestern Nigeria for Road Pavement Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sheidu S. ONIMISI, Usman B. ABDULLAHI, Hayatudden S. BARAYAIS, Abubakar M. MUHAMMAD, Abubakar G. ISAH, Abubakar S. MOHAMMED, Mohammed U. GARBA, Safety Evaluation of Orifice Plate in Natural Gas Pipeline using Computer Aided Engineering (CAE): A Step Towards Food Security , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Muhammad M. HAMIDU, Abubakar M. EL-JUMMAH, Muhammad SHUWA, An Assessment of Power Sources for Improved Energy Supply in University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Francis O. BOROKINNI, Olarewaju T. OGINNI, Ridwan O. RAJI, Kolawole ALONGE, Effects of Quenching Media and Heat Transfer Rate on the Hardness and Microstructure of Low-Carbon Steel , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chioma I. MADUEKE, Reginald UMUNAKWE, Oluwole D. ADIGUN, An Evaluation of the Porosity and Pore Volume Fractions of Coir Fibres in Relation to Their Diameters and Tensile Properties at a Crosshead Displacement Rate of 0.5 mm/Minute for Composite Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Bala YAHAYA, Mukhtar N. YAHYA, Characterization of Soil Properties Under Continuous Irrigation Practice , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Opeyemi O. ASAOLU, Oluwasanmi S. ADANIGBO, Temidayo J. AKINDAHUNSI, Advances in Privacy Preservation Techniques for Mobile Ad Hoc Networks: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olawale J. OLALUYI, Johnson O. ADEOGO, Adeniyi O. AJIBOYE, Mayowa O. ORESELU, Olarewaju T. OGINNI, Application of Machine Learning for Enhancing Fake Logo Detection , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Habibat O. YUSUFU, Yakubu D. MOHAMMED, Rose JONATHAN, Shamsuddeen SULAIMAN, Impact of Health and Safety Management on Safety Performance of Small and Medium-Sized Construction Firms in Abuja , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Enoch ADETONA, Oladiran K. ABUBAKRE, Rasheed A. MURIANA, Muhammad N. BALA, Abel A. ADEYI, Evaluation of Animal Dungs as Alternative Heat-Treating Materials in Foundry Shop , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
