Development of Enhanced Coal Briquettes for Domestic Cooking Applications in Nigeria
- Authors
-
-
Abubakar D. ADO
Author
-
Aminu D. MAHMUD
Author
-
Jamilu HARUNA
Author
-
Sadiq S. DODO
Author
-
Abdullahi YAHAYA
Author
-
- Keywords:
- Coal briquettes, calcium hydroxide, domestic cooking, combustion performance, Nigeria.
- Abstract
-
This study investigates the development of enhanced coal briquettes for domestic cooking applications in Nigeria, targeting a cleaner and affordable alternative to firewood and charcoal. Coal fines were briquetted with starch as a binder and calcium hydroxide [Ca(OH)₂] as an additive in graded proportions, yielding five formulations (F1–F5) with Ca(OH)₂ content varying from 5% to 25% at a constant 5 g of starch. The formulations were evaluated for ignition time, burning duration, ash content, and calorific value using standard laboratory procedures. A techno-economic assessment was conducted to benchmark production costs against prevalent household fuels. Results indicate that increasing Ca(OH)₂ content progressively delayed ignition (10–32 s), extended burning duration (19–45 min), and raised ash content (10–22%). Formulation F4 (20% Ca(OH)₂) provided the most balanced performance: acceptable ignition time (~25 s), extended burning duration (~38 min), moderate ash content (~13%), and calorific value of 28 MJ/kg. Estimated raw-material costs (~₦325/kg) are competitive with charcoal and kerosene. These findings indicate that enhanced coal briquettes can serve as a pragmatic transition fuel for low-income and rural Nigerian households where access to LPG is limited.
- References
- Downloads
- Published
- 17-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Abubakar D. ADO, Aminu D. MAHMUD, Jamilu HARUNA, Sadiq S. DODO, Abdullahi YAHAYA (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Muhammad M. HAMIDU, Mathew KATAMBI, Omar FARUQ, Techno-Economic and Environmental Assessment of a Solar PV-Based Microgrid for Residential Electrification in Gwange I, Maiduguri Using HOMER Pro , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ameh RICHARD, Sani B. MUHAMMAD, Terver AUSE, Umar SHEHU, Assessment of the Suitability of Wusasa Clay for Refractory Bricks Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sani MAMOUDOU, Abdulmumin A. SHUAIBU, Aliyu USMAN, Evaluation of Nano-Hydroxyapatite/Nano-Kaolin Composite Additives on the Physical Properties of Hot Mix Asphalt Binder , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Yusuf L. SHUAIB-BABATA, Kabiru S. AJAO, Yusuf O. BUSARI, Ibrahim O. AMBALI, Toheeb A. NURUDEEN, John A. OKOLO, Gabriel A. LONGE, Inhibitory Potential of Blended Parkia biglobosa and Delonix regia Extracts on Corrosion of AISI 1007 Steel in 1.0 M Hydrochloric Acid Medium , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Afeez A. AWOLOKUN, Olusegun O. ALUKO, Temitope F. AWOLUSI, Mayowa A. OGIDI, Performance Evaluation of Pervious Concrete Containing Glass Cullet and Glass Powder for Sustainable Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Usman HASSAN, An Assessment of Management Support Provided to Construction Equipment Operators Regarding Safety Practices and Protocols in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Gbenga G. OSEKE, Chisom S. AMADI, Abubakar U. RAJI, Hydrogen Production from Flare Gas via Steam Methane Reforming: A Simulation-Based Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Michael R. ADU, Blessing O. UMUKORO, Design and Construction of a 1.5 kVA Pure Sine Wave Inverter for Office Use , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Adefemi O. ADEODU, Banjo C. ADEDOKUN, Amos A. ADEGBITE, Development and Performance Evaluation of an Injection Moulding Machine for Recycled Polymer Composite Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Abdullahi YAHAYA, Ahmad ADO, Jaju A. MUHAMMAD, Zaharaddeen G. SANI, Baba A. OLUWA, Abdulazeez A. YUSUF, Kinetic Modelling of Sonocatalytic Phenol Degradation over Alumina-Supported Copper Oxide Catalyst , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
