Hydrogen Production from Flare Gas via Steam Methane Reforming: A Simulation-Based Approach
- Authors
-
-
Gbenga G. OSEKE
Author
-
Chisom S. AMADI
Author
-
Abubakar U. RAJI
Author
-
- Keywords:
- Hydrogen production; Flare gas; Steam methane reforming; DWSIM simulation; Gas flaring.
- Abstract
-
Hydrogen gas is receiving significant attention as a versatile and alternative energy carrier with the possibility of being used for different purposes in industries, including power or energy generation, chemical production, transportation, and iron and steel production, with minimal environmental impacts and concerns when produced from renewable and alternative sources. This study investigated hydrogen production from flare gas via Steam Methane Reforming (SMR) using a simulation-based approach. With Nigeria experiencing significant gas flaring challenges, the research explores converting flare gas into a valuable energy resource. Using DWSIM as the simulation tool, the SMR process was modelled under varying conditions of temperature, pressure, and steam-to-carbon (S/C) ratio. Results showed that Nigerian flare gas can achieve hydrogen yields of up to 72.9 mol% and methane conversion efficiencies exceeding 92% under optimal conditions (950°C, 5 bar, S/C = 4.0). The baseline case (850°C, 15 bar, S/C = 3.0) achieved a hydrogen yield of 68.7 mol% with 85.4% methane conversion, validating flare gas as a suitable feedstock for hydrogen production. Sensitivity analysis revealed that higher temperatures and lower pressures favoured hydrogen yield, while the optimal S/C ratio was between 2.5 and 3.5. Environmental impact analysis indicated a potential 27% reduction in CO₂ emissions compared to direct flaring, alongside elimination of unburned hydrocarbons and particulates. These findings demonstrate that flare-to-hydrogen conversion is technically feasible and environmentally beneficial, offering Nigeria a dual pathway to reduce flaring while advancing its clean energy transition.
- References
- Downloads
- Published
- 14-08-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Gbenga G. OSEKE, Chisom S. AMADI, Abubakar U. RAJI (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Daniel N. MBACHIRIN, David E. ABEL, Paul A. OMALE, Precision Agriculture Technologies for Smallholder Farming Systems in Developing Countries: A Scoping Review of Opportunities, Limitations and Future Directions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Adebola S. AKOLADE, Precious A. OLAOMOTITO, Abibat Y. ADEBIYI, Oluwatunmise P. ABOLARIN, Opeyemi I. ADETUNJI, Kola OGEDENGBE, Production and Evaluation of Cement-Bonded Composites Board Made from Banana Pseudo Stem , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ahmad ADO, Abdullahi YAHAYA, Abubakar J. MUHAMMAD, Zaharaddeen G. SANI, Baba A. OLUWA, Abdulazeez A. YUSUF, Kinetic Study of 4-Nitrophenol Sonocatalytic Degradation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mutiat S. YISA, Cross-Regional Energy Strategies: Evaluating Japan’s Power Blueprint for Nigeria’s Needs , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Babagoni A. ADAM, Muhammad B. MAINA, Muhammad SHUWA, Abba B. MUHAMMAD, A Review on Neem Leaves Valorization Through Advanced Briquetting and Carbonization Technologies , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Adefemi O. ADEODU, Banjo C. ADEDOKUN, Amos A. ADEGBITE, Development and Performance Evaluation of an Injection Moulding Machine for Recycled Polymer Composite Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Umar A. IBRAHIM, Abdulra’uf G. SHARIFAI, Hybrid CNN Feature Fusion with Optimization for Precision Potato Leaf Disease Classification , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bala ABDULLAHI, Bala G. ABDURRAHMAN, Yusuf ALHASAN, Saidu B. ABUBAKAR, Bashir I. KUNYA, Raya K. ALDADAH, Saad MAHMOUD, Ahmed REZK, Effects of Truncating the Height of Compound Parabolic Collector on its Geometry, Optical and Thermal Performances , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nsikan L. AKPAN, Akaniyene OBOT, Olusegun A. AFOLABI, Improvement of Power Efficiency of Sensor Network Using Ant Colony Optimization and K-Means Clustering Technique , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Yusuf L. SHUAIB-BABATA, Kabiru S. AJAO, Yusuf O. BUSARI, Ibrahim O. AMBALI, Kehinde O. ARUNA, Henrietta O. COKER, Toheeb A. NURUDEEN, Evaluation of UNILORIN Dam Moulding Sand Properties for Foundry Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Gbenga G. OSEKE, Fatima A. SHEHU, Muhammad K. ABBA, Effects of Completion Fluid Components on Reservoir Rock Matrix and Its Performance for Workover Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
