Assessment of Radio-Frequency Radiation Levels from Cellular Base Transceiver Stations in Residential Areas and Their Potential Health Effects on Humans
- Authors
-
-
Adesoye S. ADEGOKE
Author
-
Lateef A. OTEGBEYE
Author
-
Olufemi S. SONEYE
Author
-
Oluwole O. GREEN
Author
-
Patrick O. OLABISI
Author
-
- Keywords:
- Base Transceiver Station (BTS), Electromagnetic Radiation, Power Density, Specific Absorption ratio (SAR).
- Abstract
-
The exponential growth in need for cellular mobile communication has resulted in a significant increase in the number of base transceiver stations across the country. These base transceiver stations are known to emit electromagnetic radiations and some are located very close to residential areas. This proximity to residential areas has prompted a heightened public and scientific concern over the potential health hazard of electromagnetic radiations from base stations on human body. This research work has carried out experimental investigations aimed at estimating levels of radiations from selected base stations and evaluate their potential health risk associated with the exposure. A handheld transmogmeter was used to measure power densities across selected base transmitter stations within some densely populated areas in Ikorodu area of Lagos State. Results of our investigation show an average measured values within the ranges of 0.0064w/m2 to 0.0187w/m2. This is considered extremely low when compared with exposure safety level as recommended by International Commission on Non Ionizing Radiation Protection. From our results, it can be inferred that no significant health hazard may arise as a result of radiation exposure on human body within the limit of our experimental data.
- References
- Downloads
- Published
- 26-06-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Yusuf L. SHUAIB-BABATA, Kabiru S. AJAO, Yusuf O. BUSARI, Ibrahim O. AMBALI, Kehinde O. ARUNA, Henrietta O. COKER, Toheeb A. NURUDEEN, Evaluation of UNILORIN Dam Moulding Sand Properties for Foundry Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Oluyemi S. ONIFADE, Olusegun O. AJIDE, Development and Performance Evaluation of a Semi-Automated Impact Fracture Tester , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olusegun A. AFOLABI, Olanrewaju A. OLANITE, Nsikan L. AKPAN, Design and Simulation of a Synchronous Reference Frame-Based Active Power filter for Harmonic Mitigation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Stephen YAKUBU, Baba MAKUN, Effect of Petroleum Contamination on Soil Properties and the Removal Efficiency of Volatile Organic Compounds Using Air-Stripping System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad B. MUHAMMAD, Muhammad Y. ABDULLAHI, Aminu BALA, Optimal Reduction of Technical Power Losses in Radial Distribution Networks Using Differential Evolution for Distributed Generation: A Case Study of the Azare Substation in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Michael R. ADU, Blessing O. UMUKORO, Design and Construction of a 1.5 kVA Pure Sine Wave Inverter for Office Use , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad M. HAMIDU, Abubakar M. EL-JUMMAH, Muhammad SHUWA, An Assessment of Power Sources for Improved Energy Supply in University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mutiat S. YISA, Cross-Regional Energy Strategies: Evaluating Japan’s Power Blueprint for Nigeria’s Needs , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abdulkarim AMINU, Mohammed ALIYU, Ibrahim S. MOHAMMED, Iyanda M. ANIMASHAUN, Peter DANIEL, Mohammad USMAN, Production and Optimisation of Parameters for Density and Ash Content of Briquettes Produced from Sorghum Stalks and Groundnut Shells Using African Locust Bean (Parkia biglobosa) Pulp as a Binding Agent , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
You may also start an advanced similarity search for this article.
