BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions
- Authors
-
-
Emmanuel T. ODEYEMI
Author
-
Ya’u S. HARUNA
Author
-
Ganiyu A. BAKARE
Author
-
Hassan B. MAMMAN
Author
-
Sabo M. HASSAN
Author
-
- Keywords:
- Permanent Magnet Synchronous Generator, Maximum Power Point Tracking, Adaptive Neuro-Fuzzy Inference System, Wind Energy Conversion System, and Wind Speed.
- Abstract
-
Efficient maximum power point tracking (MPPT) in variable-speed wind energy conversion systems (WECS) is challenged by nonlinear turbine–generator dynamics and rapidly varying wind conditions, which limit the effectiveness of conventional controllers. This paper proposes an intelligent torque-based MPPT framework for a 0.5 MW grid-connected permanent magnet synchronous generator (PMSG) WECS, combining metaheuristic optimization with adaptive neuro-fuzzy control. A high-fidelity MATLAB/Simulink model integrating turbine aerodynamics, generator dynamics, and power electronic conversion is developed for systematic evaluation. Three controllers; conventional PID, BAT-optimized PID (BAT-PID), and BAT-optimized adaptive neuro-fuzzy inference system (BAT-ANFIS), are comparatively assessed under step, ramp, and turbulent wind profiles. Results show that BAT optimization improves PID transient performance by 25–30% and reduces steady-state error to 5.2%. The proposed BAT-ANFIS further achieves a 40–45% reduction in settling time relative to conventional PID and a 15–20% improvement over BAT-PID, while maintaining DC-link voltage within ±1% of nominal (950–970 V). Torque ripple is reduced by ~30%, and MPPT efficiency reaches 100% under ramp conditions and ≈98% under turbulent profiles, outperforming BAT-PID (≈86–96%) and conventional PID (≈78–88%). These results demonstrate that integrating BAT-based optimization with neuro-fuzzy adaptation significantly enhances dynamic response, robustness, and real-time power extraction, establishing BAT-ANFIS as a high-performance MPPT solution for large-scale wind energy systems.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Sirajo ALHASSAN, Abdullahi A. ADAMU, Mohammed T. JIMOH, Multi-Criteria Decision Analysis and Optimization Approaches in Sustainable Waste-to-Energy Planning: A Systematic Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Haris A. DANLADI, Umar Y. MUHAMMAD, Idris Y. IDRIS, Zaharaddeen MUSA, IoT-Based Solar-Powered Flood Early Warning System: Design and Evaluation at Alau Dam, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Muhammad M. HAMIDU, Development of MATLAB-Based Model for Solar Radiation Prediction and Photovoltaic Panel Tilt Optimization Angle for Maiduguri Region, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sirajo ALHASSAN, Abdullahi A. ADAMU, Mohammed T. JIMOH, Experimental Characterization and Seasonal Energy Potential Assessment of Municipal Solid Waste in Kano City, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Hammed A. OLASUNKANMI, Olumuyiwa I. ADENIJI, Mufutau K. LAWAL, Babatola E. OJO, Babayemi D. OMOWOLE, Somtochukwu E. AVAH, Isiaka A. ADELEKE, Kudirat N. POPOOLA, Ademidun E. IBITOYE, Design and Implementation of a Secure AI-Based Product Showcase and Customer Support System for Small and Medium-Sized Enterprises , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Oyeyemi T. AFOROLAGBA-BALOGUN, Olumide A. TOWOJU, Characterization of Fuel Produced from Nylon (Polyamide) and Polyethylene Terephthalate (PET) Wastes with Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ndagi MAMUDU, Ibrahim S. MOHAMMED, Mohammed ALIYU, Peter DANIEL, Timothy Y. AKANDE, Bala A. GARBA, Development and Performance Evaluation of Biomass Pyrolysis System for Biofuel Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nafisa A. ABDULHAMID, Danladi D. USMAN, Kabiru I. JAHUN, Rotkangmwa J. SATI, Yahaya U. JAURO, Abdulmajid M. HASHIR, Yusuf G. SHIMBURA, Development of a Solar Dryer with Multi-Products and a Residual Moisture Control System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olusola K. AKINDE, Abolaji O. ILORI, Habeeb A. ARIKEWUYO, Development of a Wearable Fall Sensing Device for Enhanced Independent Living Among the Elderly , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Taiwo J. DURODOLA, Suleiman ZUBAIR, James AGAJO, Open Radio Access Network (ORAN) Deployment Strategies for Remote Areas , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Umar A. ADAMU, Ya’u S. HARUNA, Ganiyu A. BAKARE, Buhari H. MAMMAN, Kunduli MUSTAPHA, Hadi M. ADAMU, Ismaila MAHMUD, Design and Simulation of a 200 MWp Floating Solar PV Plant Integrated with the Kainji Hydropower Plant, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
