Experimental Characterization and Seasonal Energy Potential Assessment of Municipal Solid Waste in Kano City, Nigeria
- Authors
-
-
Sirajo ALHASSAN
Author
-
Abdullahi A. ADAMU
Author
-
Mohammed T. JIMOH
Author
-
- Keywords:
- Calorific value; Energy recovery; Municipal solid waste; Seasonal variation; Waste-to-energy.
- Abstract
-
Municipal solid waste (MSW) management remains a critical environmental challenge in rapidly urbanizing regions such as Kano City, Nigeria. This study presents an experimental characterization and energy potential assessment of MSW based on seasonal variation (dry and wet seasons). Representative samples were collected from four major dumping sites: Sallari, Maimalari, Uba Gama, and Hajj Camp. Proximate and ultimate analyses were conducted to determine moisture content, ash content, volatile matter, fixed carbon, and elemental composition (C, H, O, N, and S). The results reveal clear seasonal differences in MSW properties. Moisture content ranged from ≈28.25% in the dry season to ≈44.25% in the wet season, while ash content varied between ≈28.50% and ≈31.50%. Volatile matter increased from ≈19.75% in the wet season to ≈28.40% in the dry season, and fixed carbon ranged from ≈4.50% to ≈14.85%. Ultimate analysis revealed relatively stable elemental composition across seasons, with carbon (≈45.57–46.23%), hydrogen (≈6.49–6.58%), oxygen (≈45.31–46.31%), nitrogen (≈1.42–1.43%), and sulfur (≈0.23–0.24%). These results indicate moderate fuel characteristics with variability influenced by seasonal conditions. The higher heating value (HHV) was estimated to range between ≈16.43 and ≈16.95 MJ/kg, while the lower heating value (LHV) ranged from ≈13.92 to ≈14.82 MJ/kg, with higher values observed during the dry season due to reduced moisture content. The findings suggest that although high moisture and ash contents may limit the efficiency of direct combustion, the waste stream possesses moderate energy recovery potential. Overall, the findings confirm the suitability of MSW in Kano City for thermochemical conversion technologies such as pyrolysis and gasification, particularly with appropriate pre-treatment strategies. This study provides robust, seasonally resolved experimental data for supporting sustainable waste-to-energy planning and decision-making in rapidly growing urban environments.
- References
- Downloads
- Published
- 13-04-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Tina I. FRANCIS-AKILAKI, Raymond A. EKEMUBE, Design, Construction, and Performance Evaluation of an Efficient Ethanol Stove for Domestic Cooking Application , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad M. HAMIDU, Mathew KATAMBI, Omar FARUQ, Techno-Economic and Environmental Assessment of a Solar PV-Based Microgrid for Residential Electrification in Gwange I, Maiduguri Using HOMER Pro , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abubakar D. ADO, Aminu D. MAHMUD, Jamilu HARUNA, Sadiq S. DODO, Abdullahi YAHAYA, Development of Enhanced Coal Briquettes for Domestic Cooking Applications in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Habib I. ABDULAZEEZ, Bala ABDULLAHI, Abdullahi AHMED, Ibrahim A. TUKUR, Experimental Investigation of Solar Photovoltaic Tilt Angles for Maximum Energy Harvest in Kogi State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Damilare L. ADEKEYE, Uche M. IROKA, A Microcontroller-Based Intelligent Electricity Theft Detection and Prevention System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Tunji J. ERINLE, Daniel C. UGURU-OKORIE, Abiodun M. ADEBIMPE, Adeolu A. ADEDIRAN, Hilary U. EZEA, A Comprehensive Review of In-Situ Monitoring and Post-Process Defect Detection in Additive Manufacturing , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- George AKWEC, Segun E. ADEBAYO, Caroline O. ALENOGHENA, Design and Construction of Forced-Air Heating systems for Poultry Brooding: A Comprehensive Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Francis O. BOROKINNI, Olarewaju T. OGINNI, Ridwan O. RAJI, Kolawole ALONGE, Effects of Quenching Media and Heat Transfer Rate on the Hardness and Microstructure of Low-Carbon Steel , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Auwalu M. ABDULLAHI, Musa M. BELLO, Ado HARUNA, Amina I. KHALEEL, Lubabatu B. ILA, Abdurrahaman M. BELLO, Adaptive Hybrid Compliant Control of a Desktop Upper-Limb Rehabilitation Robot , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abdulyakin USMAN, Ibrahim A. RUFAI, Dalhatu B. YAHAYA, A Review on Solar Water Heating System in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Sirajo ALHASSAN, Abdullahi A. ADAMU, Mohammed T. JIMOH, Multi-Criteria Decision Analysis and Optimization Approaches in Sustainable Waste-to-Energy Planning: A Systematic Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Koliya LAAYE, Solomon O. OGUCHE, Ibrahim I. JIDDA, Abdullahi A. ADAMU, Economic Viability of Waste-to-Energy: Pathways for Sustainable Power Generation in Jalingo, Taraba State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
