Design and Implementation of a BLE 5.0-Enabled Wearable Finger Mouse Using the XIAO nRF52840 Platform
- Authors
-
-
Suleiman ZUBAIR
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Hassan ABDULAZEEZ
Department of Cyber security Science, Federal University of Technology, Minna, Nigeria
Author
-
Bala A. SALIHU
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Abubakar A. SHUAIBU
Department of Electrical and Electronics Engineering, Abdullahi Fodio University of Science and Technology, Aliero, Nigeria
Author
-
- Keywords:
- Wearable HCI, finger mouse, BLE HID, XIAO nRF52840, joystick interface, 3D printing, low-power design.
- Abstract
-
This paper presents the design, implementation, and evaluation of a compact, ring-worn human–computer interface (HCI) device—termed the FingerMouse—that enables wireless cursor control via thumb-operated joystick input. The system uses the Seed Studio XIAO nRF52840, an ultra-compact microcontroller with native Bluetooth Low Energy (BLE) 5.0 support, to implement a standards-compliant Human Interface Device (HID) profile. This approach eliminates the need for proprietary drivers and provides plug-and-play compatibility across Windows, macOS, and Android platforms. The device operates in two modes: (1) directional cursor movement with left-click actuation, and (2) scroll-wheel emulation with deep-sleep power management. Housed in a custom 3D-printed ring (25 mm inner diameter, <15 g mass) and powered by a 90 mAh LiPo battery, the prototype achieves an average active current draw of 7.2 mA, deep-sleep consumption of <1 µA, and a usable battery life of 4.1 hours. Experimental validation with ten participants confirmed reliable operation, low latency (28 ± 5 ms), and high ergonomic comfort during extended use. This work demonstrates a low-cost, open-hardware solution that advances wearable HCI through miniaturisation, energy efficiency, and seamless OS integration.
- References
- Downloads
- Published
- 25-03-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Taiwo J. DURODOLA, Suleiman ZUBAIR, James AGAJO, Open Radio Access Network (ORAN) Deployment Strategies for Remote Areas , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Osemwegie IKPONMWOSA-EWEKA, Alexander I. IDEMUDIA, Predicting Convective Heat Transfer Coefficient in TIG Welding via Adaptive Neuro-Fuzzy Inference System (ANFIS) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Obafemi A. IBITOYE, Jemimah O. TOLU-ALALADE, Solar-Powered Low-Cost Housing: Designing Off-Grid Communities with Interlocking Stabilised Soil Blocks (ISSB) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Daniel N. MBACHIRIN, David E. ABEL, Paul A. OMALE, Precision Agriculture Technologies for Smallholder Farming Systems in Developing Countries: A Scoping Review of Opportunities, Limitations and Future Directions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad M. HAMIDU, Development of MATLAB-Based Model for Solar Radiation Prediction and Photovoltaic Panel Tilt Optimization Angle for Maiduguri Region, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Agbonyososo D. OKPERE, Kenneth K. ADAMA, Safety Concerns on the Use of Compressed Natural Gas (CNG) in the Nigerian Automobile Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar LAWAL, Abdulkadir O. ABDULBAKI, Nathaniel SALAWU, Bala A. SALIHU, Mamman A. THOMAS, Abraham U. USMAN, Sub-6 GHz Millimeter-Wave Metamaterial Antenna with Reconfigurable Radiation Patterns for Enhanced Wireless Communication , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mu’azu ABUBAKAR, Abubakar B. ALIYU, Dauda GARBA, Fabrication, Characterization, and Application of Clay-Based Ceramic Membranes for Oily Wastewater Treatment: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad M. HAMIDU, Mathew KATAMBI, Omar FARUQ, Techno-Economic and Environmental Assessment of a Solar PV-Based Microgrid for Residential Electrification in Gwange I, Maiduguri Using HOMER Pro , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Shehu ABDULKADIR, Dangora N. DAUDA, Aliyu A. ADAMU, Badaru M. SANI, Rilwan ABUBAKAR, Timothy A. TIMOTHY, Uchechukwu M. AGBOM, Abubakar S. ABUBAKAR, Development and Performance Evaluation of a Modified Active Evaporative Cooling System for Postharvest Preservation of Selected Vegetables , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Suleiman ZUBAIR, Hassan T. ABDULAZEEZ, Bala A. SALIHU, Gambo MOHAMMED, A Low-Cost, Offline-Capable Wireless Soil Moisture Monitoring System for Smallholder Farmers: Design, Validation, and Agronomic Impact , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Taiwo J. DURODOLA, Suleiman ZUBAIR, James AGAJO, Open Radio Access Network (ORAN) Deployment Strategies for Remote Areas , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar LAWAL, Abdulkadir O. ABDULBAKI, Nathaniel SALAWU, Bala A. SALIHU, Mamman A. THOMAS, Abraham U. USMAN, Sub-6 GHz Millimeter-Wave Metamaterial Antenna with Reconfigurable Radiation Patterns for Enhanced Wireless Communication , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
