Techno-Economic and Environmental Assessment of a Solar PV-Based Microgrid for Residential Electrification in Gwange I, Maiduguri Using HOMER Pro
- Authors
-
-
Muhammad M. HAMIDU
Department of Mechanical Engineering, University of Maiduguri, Maiduguri, Nigeria
Author
-
Mathew KATAMBI
Department of Mechanical Engineering, University of Maiduguri, Maiduguri, Nigeria
Author
-
Omar FARUQ
Department of Mechanical Engineering, University of Maiduguri, Maiduguri, Nigeria
Author
-
- Keywords:
- Solar PV microgrid, battery energy storage, techno-economic optimization, Homer Pro software.
- Abstract
-
The Nigerian power sector continues to struggle with outdated infrastructure, security related disruption, climate change disruptions, and unstable grid supply. In densely populated areas like Gwange I Ward, Maiduguri, centralized electricity systems remain inadequate, forcing residents to depend on costly diesel and petrol generators. This study aims to address this issue by optimizing a solar photovoltaic (PV)–battery energy storage system (BESS) microgrid. The system for Gwange I was designed and optimized using HOMER Pro v3.14, integrating load estimation, solar resource analysis, component sizing, technical performance and economic analysis into the methodological framework. Simulation results indicate that the proposed configuration comprising a 1,085 kW PV array and 1,172 kWh of usable battery storage achieves renewable penetration above 660% and delivers an annual generation of approximately 1.95 GWh. The system's competitiveness against diesel alternatives is confirmed by economic analysis, with a levelized cost of energy (LCOE) of ₦28.68/kWh and a payback period of 2.3 years. The study also highlights the importance of thermal effects on system performance, revealing a 2.7% drop in annual PV output due to temperature increase. Environmentally, noise and air pollution are reduced, and annual CO₂ emissions are reduced by over 1,300 metric tonnes. The study confirms that decentralized solar microgrids with resilience-focused design offer a sustainable, reliable route to urban electrification in weak and climate-sensitive contexts, thus directing policy for microgrid deployment and integration of thermal management.
- References
- Downloads
- Published
- 22-09-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Dandison M. WALI, Beabu B. DUMKHANA, Raymond A. EKEMUBE, Silas O. NKAKINI, Smart Assessment of Tractor Noise Levels During Tillage Operation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Martins Y. OTACHE, Iyanda M. ANIMASHAUN, Sadeeq A. MOHAMMED, Emmanuel O. AGBESE, Spatiotemporal Variability and Trend Analysis of Rainfall and Temperature in Northern Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Osagie I. IHENYEN, Raymond A. EKEMUBE, Development of an Agro-Waste Diesel Engine Powered Shredding Machine , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bala I. ABDULKARIM, Umar IDRISS, Synthesis and Characterization of Laggera aurita-Derived KOH Activated Carbon (LAKOHAC) and Role for the Adsorption of Water-Soluble Fraction of Benzene (WSFB) in Oil-Spilled Water , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Cyril OCHERI, Victor S. AIGBODION, Esther O. AMEH, Ihebuchuwu C. EZEAKU, Chibuikem A. OKAFOR, Uchenna C. AMAZUE, Eddy R. OMONIGHO, Electrochemical Analysis of Azadirachta indica Leaves as a Corrosion inhibitor on Mild Steel in 1 M H2SO4 , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Olusola K. AKINDE, Abolaji O. ILORI, Habeeb A. ARIKEWUYO, Development of a Wearable Fall Sensing Device for Enhanced Independent Living Among the Elderly , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Jamesmary E. AYANRU, Matthew S. ABOLARIN, Omotayo I. OGUNWEDE, Henry I. MORKAH, Adeshola O. OPENIBO, Development and Performance Evaluation of a Dryer for Preserving Vegetable Leaves , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Hyelni G. MSHELIA, Abdulfatai JIMOH, Mohammed A. EVUTI, Abubakar A. IBRAHIM, Abdulwahab GIWA, Adeola G. OLUGBENGA, Potential of Onion Skin, Luffa cylindrica, and Corn Cob as Cellulose Sources: A Study of Their Proximate, Ultimate, and Morphological Properties , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Bala I. ABDULKARIM, Phebe O. JAMES, Utilization of Microbial Fuel Cells for Electricity Generation from Gwagwalada Abattoir Wastewater , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Kazeem A. BELLO, Adeniyi O. ADESINA, Lukman A. OPEYEMI, Solomon O. UVIASE, The Impact of Industry 4.0 on New Product Development in Small and Medium Enterprises: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Muhammad M. HAMIDU, Abubakar M. EL-JUMMAH, Muhammad SHUWA, An Assessment of Power Sources for Improved Energy Supply in University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Muhammad M. HAMIDU, Development of MATLAB-Based Model for Solar Radiation Prediction and Photovoltaic Panel Tilt Optimization Angle for Maiduguri Region, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Hafsah A. ABDULRAHMAN, Muhammad M. HAMIDU, Techno-Economic Optimization of a Hybrid PV-Wind-Waste-to Energy System for the University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
