Experimental Investigation of Solar Photovoltaic Tilt Angles for Maximum Energy Harvest in Kogi State, Nigeria
- Authors
-
-
Habib I. ABDULAZEEZ
Rural Electrification Agency (REA), Abuja, Nigeria
Author
-
Bala ABDULLAHI
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology, Wudil, Kano State, Nigeria
Author
-
Abdullahi AHMED
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology Wudil, Kano State, Nigeria
Author
-
Ibrahim A. TUKUR
Department of Mechanical Engineering, Aliko Dangote University of Science and Technology, Wudil, Kano State, Nigeria
Author
-
- Keywords:
- Solar photovoltaic (PV) panels, tilt angle optimization, solar radiation, Kogi State, Nigeria.
- Abstract
-
This study aimed to investigate the impact of tilt angles on solar radiation, current, voltage, and power output of a photovoltaic system, while also employing mathematical modeling to predict solar radiation. This study experimentally investigates the effect of tilt angle (0°, 7.8°, 22.8°, 37.8°, and 52.8°) on the performance of 10W polycrystalline solar panels in Kogi State, Nigeria, over a 12-month period (November 2023–October 2024). Solar radiation, current, and power output were measured at 20-minute intervals using data loggers, voltmeters, and ammeters. The study only investigates the effect of tilt angle and does not consider other factors that may impact solar panel efficiency, such as dust accumulation, temperature, or shading. Results show that optimal performance varies seasonally: lower angles (0°–7.8°) yielded higher radiation and power during peak dry seasons (e.g., November, 613.67 W/m² at 22.8°), while steeper angles (22.8°–37.8°) performed better in transitional months. The 7.8° tilt achieved the highest yearly average radiation, whereas the 0° tilt produced the highest average current (0.300 A) and power (4.51 W). These findings suggest that adjusting tilt angles seasonally can maximize solar energy efficiency in Kogi State, with 7.8° recommended as the best annual fixed tilt.
- References
- Downloads
- Published
- 08-08-2025
- Section
- Articles
- License
-
Copyright (c) 2025 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Olusiji A. ADEYANJU, Joseph O. OLAIDE, Machine Learning Models for Predicting Flow Rate for Niger Delta Oil Wells , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Vincent B. ONIGBARA, Muftau A. GBENLE, Sunday I. AGU, Mechanical and Biological Performance of Titanium Hydroxyapatite Composites for Biomedical Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chioma I. MADUEKE, Reginald UMUNAKWE, Oluwole D. ADIGUN, An Evaluation of the Porosity and Pore Volume Fractions of Coir Fibres in Relation to Their Diameters and Tensile Properties at a Crosshead Displacement Rate of 0.5 mm/Minute for Composite Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Zainab B. LAPAI, Joseph A. OJENIYI, Ismail IDRIS, Abdulkadir O. ABDULBAKI, Jennifer BALA, Entropy-Guided Neural Architecture for Family-Level Classification of Windows Ransomware , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sunday IWERIOLOR, Ngozi G. EMORDI, Festus O. ISAAC, Linus CHUKWUKA, Onyekachukwu N. AKPENYI-ABOH, Liberty ANWULE, Experimental and Finite Element Investigation of Thermal Distribution and Heat Flux in an Internal Combustion Engine Cylinder , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Anthony U. AINETOR, Martins ILEVBARE, Machine Fabrication Student’s Self-Esteem and Interest in Career Choice as Correlates of their Entrepreneurial Intention in Nigerian Universities , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Taiwo J. DURODOLA, Suleiman ZUBAIR, James AGAJO, Open Radio Access Network (ORAN) Deployment Strategies for Remote Areas , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Enakhe P. OTSUPIUS, Nihad ACHEKUOGENE, Influence of Additive Manufacturing Process on the Fatigue of Polymer Materials: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Bosede A. ORHEVBA, Sodeeq A. OLAJIDE, Optimization of Alkaline Pretreatment and Fermentation Conditions for Improved Physicochemical Properties and Yield of Bioethanol Produced from Sugarcane Bagasse , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Hillary T. OGBODO, Bilkisu L. MUHAMMAD-BELLO, Joshua ABAH, Saleh E.-Y. ABDULLAHI, Quantum Computing Applications in Software Engineering: A Scoping Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
