Comparative Study of Thermal, Catalyst-Mediated, Biomass-Assisted, and Combined Upgrading Routes for Nigerian Bitumen over a Hierarchical CoMo/ZSM-5 Zeolite Catalyst
- Authors
-
-
Fadimatu N. DABAI
Author
-
Abdulkadir M. SANI
Author
-
Abdulwasiu ABDURRAHMAN
Author
-
- Keywords:
- Bitumen upgrading; heavy oil; CoMo/ZSM-5 catalyst; rice husk biomass; thermal cracking; API gravity.
- Abstract
-
Heavy oil and bitumen tend to be thick, dense, and low in API gravity, and those properties make them more expensive to extract, transport, and refine than conventional crude. This study looked at upgrading Nigerian bitumen using four different approaches: thermal cracking on its own, a hierarchical CoMo/ZSM-5 zeolite catalyst, rice husk biomass acting as a hydrogen donor, and a combined catalyst and biomass system. Each run took place in a batch reactor, with temperature raised from 25 to 350°C under an inert nitrogen atmosphere and then held for 3 hours. The upgraded products were checked for viscosity, density, and API gravity, and both the evolved gas stream and the liquid products were analyzed using Gas chromatography mass spectrometry (GCMS) and Fourier transform infrared (FTIR) spectroscopy. Viscosity dropped sharply, from 28,700 mPa s in the raw feed, down to 285.0, 91.0, 84.6, and 38.2 mPa s for the thermal, catalyst, biomass, and combined runs. API gravity rose from 7.0° to 43.2°, 40.2°, 48.5° and 12.9° across those same runs. Methane showed up as the dominant gas in every case, peaking at 57.1% around the 17 min mark in the catalyst only run. GCMS analysis showed that oxygenated alcohols dominated the thermal and catalyst runs, while carboxylic acids and alkanoate esters dominated the biomass runs; FTIR confirmed oxygenated and aliphatic groups throughout all the products. Taken together, the results show rice husk biomass and the CoMo/ZSM-5 catalyst each improve bitumen's flow properties on their own, but combining them led to an unexpected drop in API gravity, a result that calls for closer mechanistic study.
- References
- Downloads
- Published
- 17-10-2026
- Section
- Articles
- License
-
Copyright (c) 2026 Fadimatu N. DABAI, Abdulkadir M. SANI, Abdulwasiu ABDURRAHMAN (Author)

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Mathew O. ADEOTI, Victor N. HARUNA, Omolayo M. IKUMAPAYI, Timothy A. ADEKANYE, Development and Characterization of Epoxy-Based Asbestos-Free Brake Pad Composites Reinforced with Cow Hoof Particulates , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Joseph K. ZAMBWA, Jibril M. KAURA, Ocholi AMANA, Abdrasheed S. ABDURASHEED, Ejembi WILLIAMA, Evaluation of Materials and Performance Characteristics of Tannery Sludge Crumb Rubber Concrete (TSCRC) , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Mercy S. OMEIFE, Toyin Y. AKANBI, Peace D. PAUL, Mechanical Characterization of Concrete Reinforced with Sisal Fibers and Expanded Polystyrene Aggregates , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Sani MAMOUDOU, Abdulmumin A. SHUAIBU, Aliyu USMAN, Evaluation of Nano-Hydroxyapatite/Nano-Kaolin Composite Additives on the Physical Properties of Hot Mix Asphalt Binder , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Olusiji A. ADEYANJU, Joseph O. OLAIDE, Machine Learning Models for Predicting Flow Rate for Niger Delta Oil Wells , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Yetunde M. ALADEITAN, Damilola V. ABRAHAM, Abdulmojeed O. OLUOGUN, Abdulwasiu ABDURRAHMAN, A Critical Review of Surrogate Reservoir Modelling for Uncertainty Quantification in Thin Oil Rim Reservoirs , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abdullahi YAHAYA, Ahmad ADO, Jaju A. MUHAMMAD, Zaharaddeen G. SANI, Baba A. OLUWA, Abdulazeez A. YUSUF, Kinetic Modelling of Sonocatalytic Phenol Degradation over Alumina-Supported Copper Oxide Catalyst , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Opeyemi A. ASAJU, Cephas ADELORE, Akintunde O. ONAMADE, Jonathan B. ADEWUMI, Glory A. ODUBANJO, Gbenga O. WILLIAMS, Enoch O. OYELEYE, Assessing Thermal Comfort and its Impact on Student Satisfaction in Selected Hostels at Caleb University, Imota, Lagos State , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yetunde M. ALADEITAN, Abdulmojeed O. OLUOGUN, Potential of Zinc Oxide Nanoparticles for Remediation of Oil-Contaminated Soil and Water , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abdulrasheed MUSTAPHA, Kolawole O. MORAKINYO, Seyi O. FARODOYE, Rilwan B. HABEEB, Oluwatimilehin I. ADEBAMBO, Sunday F. OLAWALE, Evaluation of Green Architectural Strategies for Thermal Comfort in Four-Star Hotels in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Sulaiman Y. ADAMU, Fadimatu N. DABAI, Abdulazeez Y. ATTA, Baba Y. JIBRIL, Preparation and Characterization of Enhanced Hierarchical Zn-Ni/HZSM-5 Catalysts for Potential use in Catalytic reactions to Upgrade Bio-Oil and Hydrogen from Biomass Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ojochide P. DAMIAN, Fadimatu N. DABAI, Abdulwasiu ABDURRAHMAN, Kamiludeen OLANREWAJU, Bilyamin ABDULMUMIN, Grace A. OLUGBENGA, A Simulation-Driven Strategy for Improved Expandable Polystyrene Synthesis via Multi-Stage Initiator Dosing , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
