From Local Sand to Functional Silicon: An Integrated Pathway for Producing Photovoltaic-Grade Material from Nigerian Silica Sand
- Authors
-
-
Tahiru MOHAMMED
Author
-
Muhammad B. MAINA
Author
-
Abba B. MUHAMMAD
Author
-
Muhammad SHUWA
Author
-
- Keywords:
- Silica sand, purification, carbothermic reduction, upgraded metallurgical-grade silicon (UMG-Si), photovoltaic, local content, Nigeria.
- Abstract
-
Nigeria's significant solar energy potential is constrained by a reliance on imported high-purity silicon, despite abundant indigenous silica sand resources. This study presents a complete, integrated experimental pathway to assess the feasibility of producing photovoltaic-grade silicon from River Alau sand in Borno State. The research encompasses: Comprehensive characterization of raw sand using XRF, XRD, and SEM/EDX; Purification via optimized acid leaching (acid was used to remove impurities) and calcination; Carbothermic reduction at a temperature of 1700◦C was carried out to transform the sample to a metallurgical-grade silicon (MG-Si) and subsequent directional solidification; Evaluation of the electrical and optical properties of the upgraded silicon; and Fabrication and outdoor performance testing of simple solar cells under Maiduguri conditions. The raw sand contained 77.63% SiO₂ with significant impurities (Al₂O₃: 2.10%, K₂O: 6.31%). Purification achieved ≥99.6% SiO₂ purity, reducing key metallic impurities to <0.1%. Carbothermic reduction yielded MG-Si with 78% efficiency, and the upgraded material exhibited suitable properties for PV applications: a resistivity of 4.2 Ω•cm and a band gap of 1.12 eV. Fabricated solar cells generated an open-circuit voltage of 0.48–0.52 V. A preliminary economic analysis suggests a 25–30% potential cost saving in raw material sourcing. This work provides the first proof-of-concept for a viable domestic value chain from Nigerian silica sand to functional photovoltaic silicon, demonstrating technical feasibility and supporting the development of local solar manufacturing capabilities.
- References
- Downloads
- Published
- 29-06-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Shehu S. SHEHU, Samuel O. OLADIPUPO, Dominic S. NYITAMEN, Simulation and Performance Analysis of a Military Insignia Microstrip Patch Antenna at 2.45 GHz For Wireless Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Ahmad IDRIS, Evaluation of Challawa Tannery Wastewater as Mixing and Curing Water for Concrete Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Bala I. ABDULKARIM, Phebe O. JAMES, Utilization of Microbial Fuel Cells for Electricity Generation from Gwagwalada Abattoir Wastewater , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ayodele S. OLUWOLE, Olumayowa A. OJO, Olaitan AKINSANMI, Model Selection for Path Loss Prediction of Ultra High Frequency Terrestrial Television , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Zachariah S. PYENDANG, Felix ACHEMA, Isheni YAKUBU, Solomon E. APEH, Microstructural Characterization of Fibre Reinforced Polymer (FRP) Composite (Kenaf Fibre and Polyester Resin) for Structural Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chibuzor A. OKAFOR, Bello ABDULKAREEM, Najeem A. YEKEEN, Blessing A. OSULOYE, Yakubu O. HASSAN, Musa J. MAIKATO, Evaluation of the Effects of Charcoal Particle Sizes on Carburized Low Carbon Steel , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Hafsah A. ABDULRAHMAN, Muhammad M. HAMIDU, Techno-Economic Optimization of a Hybrid PV-Wind-Waste-to Energy System for the University of Maiduguri , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Murtala NAMAKKA, Abdulhamid S. ILIYASU, Utilisation of Supercritical Critical Fluids in Adsorption Process: A Comprehensive Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Rhoda I. ADELAJA, Ruth R. ADELAJA, Henry OTOBRISE, Adefope OWOJORI, Babatunde ADEBO, Assessment of Outdoor Radiation Exposure in an Academic Environment: A Case Study of Lead City University , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
