From Local Sand to Functional Silicon: An Integrated Pathway for Producing Photovoltaic-Grade Material from Nigerian Silica Sand
- Authors
-
-
Tahiru MOHAMMED
Author
-
Muhammad B. MAINA
Author
-
Abba B. MUHAMMAD
Author
-
Muhammad SHUWA
Author
-
- Keywords:
- Silica sand, purification, carbothermic reduction, upgraded metallurgical-grade silicon (UMG-Si), photovoltaic, local content, Nigeria.
- Abstract
-
Nigeria's significant solar energy potential is constrained by a reliance on imported high-purity silicon, despite abundant indigenous silica sand resources. This study presents a complete, integrated experimental pathway to assess the feasibility of producing photovoltaic-grade silicon from River Alau sand in Borno State. The research encompasses: Comprehensive characterization of raw sand using XRF, XRD, and SEM/EDX; Purification via optimized acid leaching (acid was used to remove impurities) and calcination; Carbothermic reduction at a temperature of 1700◦C was carried out to transform the sample to a metallurgical-grade silicon (MG-Si) and subsequent directional solidification; Evaluation of the electrical and optical properties of the upgraded silicon; and Fabrication and outdoor performance testing of simple solar cells under Maiduguri conditions. The raw sand contained 77.63% SiO₂ with significant impurities (Al₂O₃: 2.10%, K₂O: 6.31%). Purification achieved ≥99.6% SiO₂ purity, reducing key metallic impurities to <0.1%. Carbothermic reduction yielded MG-Si with 78% efficiency, and the upgraded material exhibited suitable properties for PV applications: a resistivity of 4.2 Ω•cm and a band gap of 1.12 eV. Fabricated solar cells generated an open-circuit voltage of 0.48–0.52 V. A preliminary economic analysis suggests a 25–30% potential cost saving in raw material sourcing. This work provides the first proof-of-concept for a viable domestic value chain from Nigerian silica sand to functional photovoltaic silicon, demonstrating technical feasibility and supporting the development of local solar manufacturing capabilities.
- References
- Downloads
- Published
- 29-06-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Tina I. FRANCIS-AKILAKI, Raymond A. EKEMUBE, Design, Construction, and Performance Evaluation of an Efficient Ethanol Stove for Domestic Cooking Application , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chinemeogo C. OZIOKO, Ikechukwu C.-E. IKE-EZE, Nnanyelugo O. EDWIN, Dimelu K. EBUBE, Charles MBOHWA, Investigation of the Mechanical and Thermal Properties of Waste Toner Powder Reinforced Polyester Composite for Industrial Applications , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sarafa ISHOLA, Olusegun S. OLAOYE, Adeyinka A. ADEGBOLA, Isaac A. OLUREMI, Oluseye O. AGBEDE, Drying Kinetics and Combustion Characteristics of Carbonized Cashew Nut Shell Briquettes Under Open Sun, Passive and Active Solar Drying , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Chioma I. MADUEKE, Reginald UMUNAKWE, Oluwole D. ADIGUN, An Evaluation of the Porosity and Pore Volume Fractions of Coir Fibres in Relation to Their Diameters and Tensile Properties at a Crosshead Displacement Rate of 0.5 mm/Minute for Composite Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Muazu D. ZAKARI, Md R. KAMAL, Wada I. MUHAMMAD, Nuraddeen M. NASIDI, Dahiru MOHAMMED, Agro-Hydrological Modelling Systems in Peninsula Malaysia: A Comprehensive Review and a Guide towards Model Development , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Sheidu S. ONIMISI, Usman B. ABDULLAHI, Hayatudden S. BARAYAIS, Abubakar M. MUHAMMAD, Abubakar G. ISAH, Abubakar S. MOHAMMED, Mohammed U. GARBA, Safety Evaluation of Orifice Plate in Natural Gas Pipeline using Computer Aided Engineering (CAE): A Step Towards Food Security , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Olawale J. OLALUYI, Johnson O. ADEOGO, Aduragbemi F. OJO, Olarewaju T. OGINNI, Design and Construction of Transistor Based Water Level Indicator Tank with Overflow Alarm , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Olatunde A. AKANO, Wariz A. ISMAEL, Ayomikun A. AWOSEYI, Femi AYO, Ifeoluwa M. OLANIYI, Jide E.T. AKINSOLA, Short Messaging Service Spam Detection Model Using Natural Language Processing and Deep Learning Techniques , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yusuf M. YAHAYA, Factors Contributing to the Erosion of Freehand Sketching Competence in Technology Education: A Case Study of Bayero University, Kano , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Samuel O. OLADIPUPO, Dominic S. NYITAMEN, Lanre S. MOJEREOLA, Design, Simulation and Fabrication of a Slot Loaded 2.45 GHz Microstrip Patch Antenna for ISM Band Wireless Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
