Assessment of Radio-Frequency Radiation Levels from Cellular Base Transceiver Stations in Residential Areas and Their Potential Health Effects on Humans
- Authors
-
-
Adesoye S. ADEGOKE
Author
-
Lateef A. OTEGBEYE
Author
-
Olufemi S. SONEYE
Author
-
Oluwole O. GREEN
Author
-
Patrick O. OLABISI
Author
-
- Keywords:
- Base Transceiver Station (BTS), Electromagnetic Radiation, Power Density, Specific Absorption ratio (SAR).
- Abstract
-
The exponential growth in need for cellular mobile communication has resulted in a significant increase in the number of base transceiver stations across the country. These base transceiver stations are known to emit electromagnetic radiations and some are located very close to residential areas. This proximity to residential areas has prompted a heightened public and scientific concern over the potential health hazard of electromagnetic radiations from base stations on human body. This research work has carried out experimental investigations aimed at estimating levels of radiations from selected base stations and evaluate their potential health risk associated with the exposure. A handheld transmogmeter was used to measure power densities across selected base transmitter stations within some densely populated areas in Ikorodu area of Lagos State. Results of our investigation show an average measured values within the ranges of 0.0064w/m2 to 0.0187w/m2. This is considered extremely low when compared with exposure safety level as recommended by International Commission on Non Ionizing Radiation Protection. From our results, it can be inferred that no significant health hazard may arise as a result of radiation exposure on human body within the limit of our experimental data.
- References
- Downloads
- Published
- 26-06-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Hafsa K. AHMAD, Graph-Augmented Transformers for Hausa Sentiment Analysis: When Does Graph Structure Help? , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Danladi K. GARBA, Emmanuel O. AWEDA, Nuhu A. ADEMOH, Fredrick NGOLEMASANGO, Pascal A. UBI, Akor TERNGU, Lawal KABIR, Shuaibu O. YAKUBU, The Effects of Gum Arabic Matrix on the Hardness and Water Absorption of Agro-Based (Banana Pseudostem) Hybrid Composites , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Vincent B. ONIGBARA, Muftau A. GBENLE, Sunday I. AGU, Mechanical and Biological Performance of Titanium Hydroxyapatite Composites for Biomedical Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Aminu BALA, Nasiru B. KADANDANI, Isiyaku ABUBAKAR, Performance Evaluation of Fuzzy Logic and Fractional Order PI Controllers for Electric Vehicle Wireless Charging System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ibrahim M. GANA, Abdullahi YUSUF, Agidi GBABO, Micheal EPHRAIM, Abubakar M. HASSAN, Development and Testing of an Automated Solar-Powered Nutrient Film Technique (NFT) Hydroponic Planting System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ruth R. ADELAJA, Rhoda I. ADELAJA, Henry OTOBRISE, Adefope OWOJORI, Babatunde ADEBO, Investigation of Indoor Radiation Levels within Lead City University’s Academic Buildings , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Israel A. OLUWAFEMI, Akaninyene B. OBOT, Emmanuel UBOM, Ayodele A. OLATUNJI, Mbuotidem G. ROBINSON, Design and Analysis of a Dual-Band Circular Microstrip Antenna Using Spatially Distributed CSRRs , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Adebola S. AKOLADE, Precious A. OLAOMOTITO, Abibat Y. ADEBIYI, Oluwatunmise P. ABOLARIN, Opeyemi I. ADETUNJI, Kola OGEDENGBE, Production and Evaluation of Cement-Bonded Composites Board Made from Banana Pseudo Stem , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Aminu D. MAHMUD, Imran N. IBRAHIM, Development and Optimization of Starch-Based Bioplastics from Millet and Cassava Using Mixture Design Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
