Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System
- Authors
-
-
Emmanuel T. ODEYEMI
Author
-
Ya’u S. HARUNA
Author
-
Ganiyu A. BAKARE
Author
-
Hassan B. MAMMAN
Author
-
Sabo M. HASSAN
Author
-
- Keywords:
- Adaptive Particle Swarm Optimization, Maximum Power Point Tracking, Software-in-the-Loop, Solar Photovoltaic Systems, and Dynamic Irradiance.
- Abstract
-
Maximum Power Point Tracking (MPPT) is essential for maximizing energy yield in photovoltaic (PV) systems under dynamic environmental conditions. This study presents a comparative evaluation and real-time Software-in-the-Loop (SIL) validation of conventional and intelligent MPPT algorithms for a 1.5 MW standalone PV system, representing a utility-scale installation with high current and dynamic complexity. The Adaptive Particle Swarm Optimization (APSO) algorithm is characterized by dynamic adjustments of inertia weight and acceleration coefficients, enhancing convergence speed and tracking accuracy. A high-fidelity MATLAB/Simulink model, integrating a DC–DC boost converter and dynamic irradiance profiles, was developed. P&O, INC, GA, and APSO were evaluated based on tracking efficiency, convergence speed, and steady-state ripple. The results show that APSO achieved the highest tracking efficiency (99.3%), the fastest convergence (0.8 s), and the lowest ripple (1.8%), outperforming GA, P&O, and INC. SIL validation further confirmed the feasibility and robustness of APSO, maintaining 99.0% efficiency and 1.6% ripple under real-time constraints. These findings establish APSO as a reliable, implementation-ready MPPT solution for large-scale PV systems.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Aminu D. MAHMUD, Imran N. IBRAHIM, Development and Optimization of Starch-Based Bioplastics from Millet and Cassava Using Mixture Design Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olusola K. AKINDE, Abolaji O. ILORI, Habeeb A. ARIKEWUYO, Development of a Wearable Fall Sensing Device for Enhanced Independent Living Among the Elderly , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Shehu ABDULKADIR, Dangora N. DAUDA, Aliyu A. ADAMU, Badaru M. SANI, Rilwan ABUBAKAR, Timothy A. TIMOTHY, Uchechukwu M. AGBOM, Abubakar S. ABUBAKAR, Development and Performance Evaluation of a Modified Active Evaporative Cooling System for Postharvest Preservation of Selected Vegetables , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Samuel E. CHUKWU, Martins Y. OTACHE, Precious O. ATEMOAGBO, Emmanuel O. AGBESE, Copula-Based Modelling of Drought Severity-Duration-Frequency Relationship of Sokoto-Rima-River Basin, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abba M. BALA, Abdurrauf G. SHARIFAI, Umar S. HARUNA, A Hybrid Deep Learning Model for Efficient Anomaly Detection in Video Surveillance Systems , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Luqman K. SALATI, Sani D. MUHAMMAD, Jacob T. ADEYEMO, Simulation of Trucks Haulage Operation at Ashaka Cement Company in Gombe State, North-Eastern Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Idris M. WADA, Abba IBRAHIM, Genesis ISHAYA, Performance Evaluation of Climate Products with Validation Using Bootstrapping and Climate Extremes in the Hadejia-Jama’are River Basin, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mokọ́ládé JOHNSON, Bashir SALIM, Enobong EQUERE, Miriam I. CHUKWUMA-UCHEGBU, Emma EKPO, Ali B. ABDULSALAM, Conserving Indigenous Geometries: A Vital Approach to Integrating Cultural Heritage into Architectural Education , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Amina UTHMAN, Shamsuddeen SULAIMAN, Evaluation of Cost Factors Influencing the Adoption of Sustainable Construction Practices in Abuja, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ibrahim BALA, Solomon M. DAUDA, Audu A. BALAMI, Peter A. IDAH, Design Analysis of a Kenaf Decorticating Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
