Software-in-the-Loop Validation of an Adaptive Particle Swarm Optimization-Based MPPT Controller for Real-Time Photovoltaic System
- Authors
-
-
Emmanuel T. ODEYEMI
Author
-
Ya’u S. HARUNA
Author
-
Ganiyu A. BAKARE
Author
-
Hassan B. MAMMAN
Author
-
Sabo M. HASSAN
Author
-
- Keywords:
- Adaptive Particle Swarm Optimization, Maximum Power Point Tracking, Software-in-the-Loop, Solar Photovoltaic Systems, and Dynamic Irradiance.
- Abstract
-
Maximum Power Point Tracking (MPPT) is essential for maximizing energy yield in photovoltaic (PV) systems under dynamic environmental conditions. This study presents a comparative evaluation and real-time Software-in-the-Loop (SIL) validation of conventional and intelligent MPPT algorithms for a 1.5 MW standalone PV system, representing a utility-scale installation with high current and dynamic complexity. The Adaptive Particle Swarm Optimization (APSO) algorithm is characterized by dynamic adjustments of inertia weight and acceleration coefficients, enhancing convergence speed and tracking accuracy. A high-fidelity MATLAB/Simulink model, integrating a DC–DC boost converter and dynamic irradiance profiles, was developed. P&O, INC, GA, and APSO were evaluated based on tracking efficiency, convergence speed, and steady-state ripple. The results show that APSO achieved the highest tracking efficiency (99.3%), the fastest convergence (0.8 s), and the lowest ripple (1.8%), outperforming GA, P&O, and INC. SIL validation further confirmed the feasibility and robustness of APSO, maintaining 99.0% efficiency and 1.6% ripple under real-time constraints. These findings establish APSO as a reliable, implementation-ready MPPT solution for large-scale PV systems.
- References
- Downloads
- Published
- 23-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Mu’azu ABUBAKAR, Abubakar B. ALIYU, Dauda GARBA, Fabrication, Characterization, and Application of Clay-Based Ceramic Membranes for Oily Wastewater Treatment: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar L. IBRAHEEM, John K. ALHASSAN, Noel D. MOSES, Suleiman AHMAD, Development of Ensemble SVM–LSTM Model for Phishing Website Detection , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Raji ABDULRASAK, Abdulaziz S. ALIYU, Assessment of Occupational Health Hazards Among Oil Refinery Workers at Kaduna Refining and Petrochemical Company , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Dandison M. WALI, Beabu B. DUMKHANA, Raymond A. EKEMUBE, Silas O. NKAKINI, Smart Assessment of Tractor Noise Levels During Tillage Operation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Hammed A. OLASUNKANMI, Olumuyiwa I. ADENIJI, Mufutau K. LAWAL, Babatola E. OJO, Babayemi D. OMOWOLE, Somtochukwu E. AVAH, Isiaka A. ADELEKE, Kudirat N. POPOOLA, Ademidun E. IBITOYE, Design and Implementation of a Secure AI-Based Product Showcase and Customer Support System for Small and Medium-Sized Enterprises , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Benedict O. EDENSETING, Innocent O. OBOH, Alexander A. JOCK, Effective Food Waste Utilization: A Veritable Source of Biofuel for Nigerian Economic Sustenance and Development - A Review , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Hyelni G. MSHELIA, Abdulfatai JIMOH, Mohammed A. EVUTI, Abubakar A. IBRAHIM, Abdulwahab GIWA, Adeola G. OLUGBENGA, Potential of Onion Skin, Luffa cylindrica, and Corn Cob as Cellulose Sources: A Study of Their Proximate, Ultimate, and Morphological Properties , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ahmad ADO, Abdullahi YAHAYA, Abubakar J. MUHAMMAD, Zaharaddeen G. SANI, Baba A. OLUWA, Abdulazeez A. YUSUF, Kinetic Study of 4-Nitrophenol Sonocatalytic Degradation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kamoru O. OLADOSU, Kabiru MUSTAPHA, Ayodeji S. OLAWORE, Akeem B. IBRAHIM, Abdulganiyu ISSA, Development of a Free-Fall Pyrolysis Reactor for Biofuel Production Using Sugarcane Bagasse and Cassava Rhizomes as Feedstocks , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Kayode A. IDOWU, Victory N. JESSEY, Emmanuel B. SAMANI, The Role of Aesthetic Properties of Granitic Dimension Stones on Marketability: A Case Study of CIBI Nigeria Limited, Kaduna State , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Emmanuel T. ODEYEMI, Ya’u S. HARUNA, Ganiyu A. BAKARE, Hassan B. MAMMAN, Sabo M. HASSAN, BAT-Optimized PID and ANFIS Torque-Based MPPT for a 0.5 MW PMSG-Based Wind Energy Conversion System Under Dynamic Wind Conditions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mela I. L. LASHIRU, Ganiyu A. BAKARE, Sabo M. HASSAN, Kamilu O. LAWAL, Data-Driven Observability Enhancement in Active Distribution Networks via Optimal Co-Deployment of DGs and D-PMUs Using Hybrid APSO-ASDA , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Umar A. ADAMU, Ya’u S. HARUNA, Ganiyu A. BAKARE, Buhari H. MAMMAN, Kunduli MUSTAPHA, Hadi M. ADAMU, Ismaila MAHMUD, Design and Simulation of a 200 MWp Floating Solar PV Plant Integrated with the Kainji Hydropower Plant, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
