Assessment of the Impact of Tractor Noise Exposure on Operators and Bystanders
- Authors
-
-
Beabu B. DUMKHANA
Author
-
Dandison M. WALI
Author
-
- Keywords:
- Agricultural machinery, noise exposure, setback distance, hearing impairment.
- Abstract
-
Rising noise levels from agricultural machinery contributed to environmental and occupational health issues, adversely affecting machine operators. This study investigated the impact of noise on operators and bystanders during tillage operations. A field experiment covering 1.10703 acres of land was divided into three blocks, each with 9 subplots measuring 160 × 38 m, for a total of 27 treatments in a randomized complete block design (RCBD). The generated noise data were used to create noise distribution trends for different tractor speeds during ploughing, harrowing, and ridging operations. The findings showed that increasing tractor speed from 5 to 9 km/h raised noise levels from 54 to 83.3 dB, affecting individual performance and productivity. As recommended by NESREA in 2007, harrowing met the noise level of 70 dB, while ploughing and ridging were 83.3 dB. Regression analysis revealed strong correlations (r² = 0.8073–0.995) between setback distance and noise reduction. This study has shown that tractor operators may experience temporary hearing loss when leaving the work environment in addition to cognitive fatigue.
- References
- Downloads
- Published
- 15-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Ruth R. ADELAJA, Rhoda I. ADELAJA, Henry OTOBRISE, Adefope OWOJORI, Babatunde ADEBO, Investigation of Indoor Radiation Levels within Lead City University’s Academic Buildings , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Munir A. ADEWOYE, Ahmed ALIYU, Usman A. ALI, Abdulrasheed JIMOH, Blockchain-Based Food Supply Chain Traceability: A Systematic Review of Privacy Preserving and Scalability , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Nafisa A. ABDULHAMID, Danladi D. USMAN, Kabiru I. JAHUN, Rotkangmwa J. SATI, Yahaya U. JAURO, Abdulmajid M. HASHIR, Yusuf G. SHIMBURA, Development of a Solar Dryer with Multi-Products and a Residual Moisture Control System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bala YAHAYA, Mukhtar N. YAHYA, Characterization of Soil Properties Under Continuous Irrigation Practice , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Nnamdi S. OKOMBA, Adedayo A. SOBOWALE, Adebimpe O. ESAN, Bolaji A. OMODUNBI, Taiwo A. AWOYEMI, Development of an Intelligent-Based Elevator System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Suleiman ZUBAIR, Hassan T. ABDULAZEEZ, Bala A. SALIHU, Gambo MOHAMMED, A Low-Cost, Offline-Capable Wireless Soil Moisture Monitoring System for Smallholder Farmers: Design, Validation, and Agronomic Impact , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Peter S. IDOKO, Iyinoluwa T. IDOWU, Emmanuel O. AYODELE, Temitope F. SHOLANKE, Peter A. IDOWU, Machine Learning Based Feature Selection for Early Detection of Thyroid Disorders in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Koliya LAAYE, Solomon O. OGUCHE, Ibrahim I. JIDDA, Abdullahi A. ADAMU, Economic Viability of Waste-to-Energy: Pathways for Sustainable Power Generation in Jalingo, Taraba State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yahaya U. JAURO, Danladi D. USMAN, Lawan G. ABUBAKAR, Yusuf G. SHIMBURA, Aminu MOHAMMED, Design and Fabrication of Tapered Screw Briquetting Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Daniel N. MBACHIRIN, David E. ABEL, Paul A. OMALE, Precision Agriculture Technologies for Smallholder Farming Systems in Developing Countries: A Scoping Review of Opportunities, Limitations and Future Directions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Dandison M. WALI, Beabu B. DUMKHANA, Raymond A. EKEMUBE, Silas O. NKAKINI, Smart Assessment of Tractor Noise Levels During Tillage Operation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
