Evaluation on the Rheological Properties of Water-Based Drilling Mud: A Case Study of Ire-Ekiti Clay
- Authors
-
-
Joseph O. AJAYI
Author
-
Adekunle T. ADENIYI
Author
-
Mufliah G. OMOFOYEWA
Author
-
Abel A. ADEYI
Author
-
Abdulwahab GIWA
Author
-
- Keywords:
- Ire-Ekiti clay, beneficiation, bentonite, rheological properties, water-based mud.
- Abstract
-
Rheological properties are tested throughout a drilling operation as it is critical in the control and maintenance of rheological properties. This paper investigates the evaluation on the Marsh funnel viscosity, apparent viscosity, and fluid loss of water-based drilling mud. The native clay originated in Ire-Ekiti, Ekiti State, Nigeria. In order to create water-based mud, the characteristics of the clay were determined and compared with those of bentonite, the preferred clay for drilling operations. The results show that the generated drilling fluid's pH levels and rheological characteristics differ significantly from bentonite. This is due to the fact that it attracts clay and water, and the low concentration of sodium cations (Na++) prevents it from swelling. When the local mud was beneficiated using soda ash (Na2CO3) at a concentration of 5.0 g clay at 63 microns screen size to 350 ml of the mud, the pH rose by 15.2% from 8.11 to 11.02 and by 8% from 10.00 to 11.73. When PAC-HV was added to the combination, water loss significantly decreased by 32.8% and 66.8%, while marsh funnel viscosity increased by 4.4% and 7.6%, apparent viscosity fell by 26.6% at 63 microns sieve size, and severely rose by 55.8% at 150 microns filter size. After adding 10 g of barite (BaSO4) to 350 ml of the mixture, the clay density rose by 1.2% at both sieve sizes, from 8.50 lb/gal to 8.70 lb/gal. Therefore, the Ire clay has good rheological properties at substantial concentrations when beneficiated with soda ash (Na2CO3), which would compare favorably with those of bentonite; however, PAC-HV must be increased above 1.0 g at 150 microns filter size. Ire clay can therefore be used to make a drilling fluid.
- References
- Downloads
- Published
- 09-05-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Abdulrahman B. GAMBO, Carbon Capture and Mechanical Design of Membrane Reactors: A Systematic Review and Design-Performance Framework for Sustainable Energy Systems , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad M. ABDULLAHI, Iyanda M. ANIMASHAUN, Ibrahim A. ABDULFATAI, George U. STEPHEN, Spatial Scale Effects on the Relationship Between Land Use/Land Cover Change and Potential Evapotranspiration in Niger State, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Yusuf M. YAHAYA, Factors Contributing to the Erosion of Freehand Sketching Competence in Technology Education: A Case Study of Bayero University, Kano , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Opeyemi O. ASAOLU, Oluwasanmi S. ADANIGBO, Temidayo J. AKINDAHUNSI, Advances in Privacy Preservation Techniques for Mobile Ad Hoc Networks: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Ayodele S. OLUWOLE, Olumayowa A. OJO, Olaitan AKINSANMI, Model Selection for Path Loss Prediction of Ultra High Frequency Terrestrial Television , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Enakhe P. OTSUPIUS, Nihad ACHEKUOGENE, Influence of Additive Manufacturing Process on the Fatigue of Polymer Materials: A Review , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Abdullahi P. NUHU, Kabir O. YUSUF, Aliyu O. ABDULRAHMAN, Kehinde A. LASISI, Effect of Heat Treatment on Post Weld Railway Track , FUDMA Journal of Engineering and Technology: Vol. 1 No. 1 (2025): July 2025
- Johnson O. ADEOGO, Olawale J. OLALUYI, Olumuyiwa A. OJO, Abayomi T. AYODELE, Elijah A. OLAJUYIN, Fasasi BELLO, Paul C. OFODU, Performance Evaluation of 3.5 kVA Hybrid Inverter Following Standard Engineering Practices and Safety Procedures , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Mohammed K. BASHIR, Sanusi A. DARMA, Usman MAHMUD, Mansir ABUBAKAR, Enhanced Breast Cancer Classification Using Ensemble Learning and Data Resampling Techniques: A Machine Learning Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Aliu S. SALIU, Ejike C. ANENE, Buhari M. HASSAN, Sabo M. HASSAN, Salisu H. MOHAMMED, Nafisa S. USMAN, Addressing Resource Allocation Challenges in Wireless Networks with Cultural Smell Agent Optimization Algorithms: A Literature Survey , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Salisu MOHAMMED, Abdulfatai JIMOH, Abdullahi M. EVUTI, Abdulwahab GIWA, Abubakar A. IBRAHIM, Pretreatment and Characterization of Selected Precursors for Chitin/Chitosan Production , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ephraim G. KEFAS, Abdulfatai JIMOH, Mohammed A. EVUTI, Abubakar A. IBRAHIM, Abdulwahab GIWA, Adeola G. OLUGBENGA, Luffa Sponge, Banana Stem and Delonix regia Seed Characterization as Potential Biosorbents for Industrial Wastewater Remediation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Hyelni G. MSHELIA, Abdulfatai JIMOH, Mohammed A. EVUTI, Abubakar A. IBRAHIM, Abdulwahab GIWA, Adeola G. OLUGBENGA, Potential of Onion Skin, Luffa cylindrica, and Corn Cob as Cellulose Sources: A Study of Their Proximate, Ultimate, and Morphological Properties , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
