Evaluation of the Agricultural Best Management Practices (ABMPs) and Their Effect on Discharge Reduction of Shiroro Dam Site using SWAT Model
- Authors
-
-
Ibrahim A. KUTI
Author
-
Sunday E. OGUNMOLA
Author
-
Peter A. ADEOYE
Author
-
- Keywords:
- Discharge, Agricultural Best Management Practices, ArcSWAT, SWAT model, SUFI2, Shiroro Dam site.
- Abstract
-
Best Management Practices (BMPs) have proven to be effective in reducing erosion, sediment yield, and nutrient loss. However, there is little information on their effects on annual inflow. This study used the SWAT model to delineate the Shiroro Dam, divide it into 18 subbasins and 35 hydrological response units, and further modifies the curve number and support practice factor to represent terrace, contour, and strip cropping on the agricultural land. The research calibrated and validated the inflow data from 2011 to 2021. Sequential Uncertainty Fitting (SUFI2) algorithm was used to perform calibration and validation. Whereas the objective function used was Nash-Sutcliffe efficiency (NSE). Other performance indices identified included the coefficient of determination (R²), P-factor, r-factor, and Percent Bias (PBIAS). The results show that the NSE values ranged from 0.58 to 0.65 in the validation stage. It implies that the models are satisfactory. In addition, the sensitivity analysis revealed that saturated hydraulic conductivity (SOL_K) was highly sensitive to inflow under terrace, contour, and strip cropping, with the highest t- statistic, implying that SOL_K influences the simulated inflow in the catchment. The percentage reductions in inflow under terrace, contour, and strip cropping were 23%, 8%, and 1.3%, respectively. It implies that terrace and contour implementations would reduce annual inflow to the Shiroro Dam and serve as appropriate conservation practices in the study area.
- References
- Downloads
- Published
- 25-04-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Nuhu MOHAMMED, Garkuwa Y. ADAMU, Abubakar A. FACHWAY, Aminu MOHAMMED, Afolayan A. OLASUNKANMI, Odoh F. CHIMEZIE, Muhammad A. YUSUF, Development of A Water-Recycling Pico Hydropower System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Adebola S. AKOLADE, Precious A. OLAOMOTITO, Abibat Y. ADEBIYI, Oluwatunmise P. ABOLARIN, Opeyemi I. ADETUNJI, Kola OGEDENGBE, Production and Evaluation of Cement-Bonded Composites Board Made from Banana Pseudo Stem , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Vincent B. ONIGBARA, Muftau A. GBENLE, Sunday I. AGU, Mechanical and Biological Performance of Titanium Hydroxyapatite Composites for Biomedical Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Usman GARBA, Abdullahi ADAMU, Mamuda MUHAMMAD, Physicochemical Characterisation of Mineral Sands from Northwestern Nigeria for Industrial Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Agbonyososo D. OKPERE, Kenneth K. ADAMA, Safety Concerns on the Use of Compressed Natural Gas (CNG) in the Nigerian Automobile Industry , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Isaac O. UKRAKPO, Osemwegie IKPONMWOSA-EWEKA, Prediction of Weld Strain Using Artificial Neural Network: A Modeling Approach , FUDMA Journal of Engineering and Technology: Vol. 2 No. 2 (2026): December 2026
- Damilare L. ADEKEYE, Isiyaku SALEH, Yemisi E. AKINSELI, Design and Implementation of an Automatic Gate for Cars at Railway Crossings , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Damilare L. ADEKEYE, Uche M. IROKA, A Microcontroller-Based Intelligent Electricity Theft Detection and Prevention System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Zachariah S. PYENDANG, Felix ACHEMA, Isheni YAKUBU, Solomon E. APEH, Microstructural Characterization of Fibre Reinforced Polymer (FRP) Composite (Kenaf Fibre and Polyester Resin) for Structural Applications , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sulaiman Y. ADAMU, Fadimatu N. DABAI, Abdulazeez Y. ATTA, Baba Y. JIBRIL, Preparation and Characterization of Enhanced Hierarchical Zn-Ni/HZSM-5 Catalysts for Potential use in Catalytic reactions to Upgrade Bio-Oil and Hydrogen from Biomass Pyrolysis , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Abubakar S. MOHAMMED, Mohammed ALIYU, Mohammed U. GARBA, Ibrahim S. MOHAMMED, Ibrahim A. KUTI, Meshack S. IMOLOGIE, Umaru MUSA, Olalekan D. ADENIYI, Peter A. ADEOYE, Abubakar G. ISAH, Folarin T. OLORUNMOTITO, Development and Packaging of Eco-friendly Biosolid Briquettes Synthesised with Bagasse for Green Energy Generation and Utilisation , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
