Design and Implementation of a BLE 5.0-Enabled Wearable Finger Mouse Using the XIAO nRF52840 Platform
- Authors
-
-
Suleiman ZUBAIR
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Hassan ABDULAZEEZ
Department of Cyber security Science, Federal University of Technology, Minna, Nigeria
Author
-
Bala A. SALIHU
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Abubakar A. SHUAIBU
Department of Electrical and Electronics Engineering, Abdullahi Fodio University of Science and Technology, Aliero, Nigeria
Author
-
- Keywords:
- Wearable HCI, finger mouse, BLE HID, XIAO nRF52840, joystick interface, 3D printing, low-power design.
- Abstract
-
This paper presents the design, implementation, and evaluation of a compact, ring-worn human–computer interface (HCI) device—termed the FingerMouse—that enables wireless cursor control via thumb-operated joystick input. The system uses the Seed Studio XIAO nRF52840, an ultra-compact microcontroller with native Bluetooth Low Energy (BLE) 5.0 support, to implement a standards-compliant Human Interface Device (HID) profile. This approach eliminates the need for proprietary drivers and provides plug-and-play compatibility across Windows, macOS, and Android platforms. The device operates in two modes: (1) directional cursor movement with left-click actuation, and (2) scroll-wheel emulation with deep-sleep power management. Housed in a custom 3D-printed ring (25 mm inner diameter, <15 g mass) and powered by a 90 mAh LiPo battery, the prototype achieves an average active current draw of 7.2 mA, deep-sleep consumption of <1 µA, and a usable battery life of 4.1 hours. Experimental validation with ten participants confirmed reliable operation, low latency (28 ± 5 ms), and high ergonomic comfort during extended use. This work demonstrates a low-cost, open-hardware solution that advances wearable HCI through miniaturisation, energy efficiency, and seamless OS integration.
- References
- Downloads
- Published
- 25-03-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Mathew O. ADEOTI, Victor N. HARUNA, Omolayo M. IKUMAPAYI, Timothy A. ADEKANYE, Development and Characterization of Epoxy-Based Asbestos-Free Brake Pad Composites Reinforced with Cow Hoof Particulates , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Mohammed A. GANA, Zaka A. MSHELIA, Isuwa S. AJI, Alhaji GUJJA, Lawan A.M. KOLO, Investigation and Comparative Analysis of Natural Moulding Sands from Five Deposits in Maiduguri, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Michael R. ADU, Afeez O. OLAWUNMI, Design and Implementation of an IoT-Based Smart Attendance System , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Muhammad B. MUHAMMAD, Noor S. B. MANSOR, Fariha R. KHAN, Investigating Breakdown Strength Based on Trapping Profile in Cross-Linked Polyethylene (XLPE) Nanocomposites , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Kamoru O. OLADOSU, Kabiru MUSTAPHA, Ayodeji S. OLAWORE, Akeem B. IBRAHIM, Abdulganiyu ISSA, Development of a Free-Fall Pyrolysis Reactor for Biofuel Production Using Sugarcane Bagasse and Cassava Rhizomes as Feedstocks , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Usman A. ALI, Munir A. ADEWOYE, Adamu U. ABDULLAHI, Determinants of Blockchain Adoption for Academic Certificate Verification: Insights from Verification Officers for Sustainable Education in Nigerian Higher Education Institutions , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Peter S. IDOKO, Iyinoluwa T. IDOWU, Emmanuel O. AYODELE, Temitope F. SHOLANKE, Peter A. IDOWU, Machine Learning Based Feature Selection for Early Detection of Thyroid Disorders in Nigeria , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Olarewaju T. OGINNI, An Overview of Unmanned Aerial Vehicles Technologies for Office Use and Services Delivery , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Victoria A. UMEJURU, Isaac E. IHUA-MADUENYI, Adaobi S. NWOSI-ANELE, Performance Evaluation and Economic Assessment of Electrical Submersible Pumps for Heavy Oil Production in Mature Niger Delta Oilfields , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Afeez A. AWOLOKUN, Olusegun O. ALUKO, Temitope F. AWOLUSI, Mayowa A. OGIDI, Performance Evaluation of Pervious Concrete Containing Glass Cullet and Glass Powder for Sustainable Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Suleiman ZUBAIR, Hassan T. ABDULAZEEZ, Bala A. SALIHU, Gambo MOHAMMED, A Low-Cost, Offline-Capable Wireless Soil Moisture Monitoring System for Smallholder Farmers: Design, Validation, and Agronomic Impact , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Taiwo J. DURODOLA, Suleiman ZUBAIR, James AGAJO, Open Radio Access Network (ORAN) Deployment Strategies for Remote Areas , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Abubakar LAWAL, Abdulkadir O. ABDULBAKI, Nathaniel SALAWU, Bala A. SALIHU, Mamman A. THOMAS, Abraham U. USMAN, Sub-6 GHz Millimeter-Wave Metamaterial Antenna with Reconfigurable Radiation Patterns for Enhanced Wireless Communication , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
