A Low-Cost, Offline-Capable Wireless Soil Moisture Monitoring System for Smallholder Farmers: Design, Validation, and Agronomic Impact
- Authors
-
-
Suleiman ZUBAIR
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Hassan T. ABDULAZEEZ
Department of Cyber-Security Science, Federal University of Technology, Minna, Nigeria
Author
-
Bala A. SALIHU
Department of Telecommunication Engineering, Federal University of Technology, Minna, Nigeria
Author
-
Gambo MOHAMMED
Department of Electrical and Electronic Engineering, Abdullahi Fodio University of Science and Technology, Aliero, Kebbi State, Nigeria
Author
-
- Keywords:
- Soil moisture monitoring, smart irrigation, capacitive sensor, GSM-SMS, ESP32, water-use efficiency, smallholder agriculture, open-source hardware, precision farming.
- Abstract
-
Water scarcity and inefficient irrigation practices significantly constrain agricultural productivity, particularly among smallholder farmers in sub-Saharan Africa. Although precision agriculture technologies offer potential solutions, most existing systems are costly, require continuous internet connectivity, or involve complex technical infrastructures, limiting their adoption in resource-constrained environments. This paper presents a low-cost, offline-capable wireless soil moisture monitoring and irrigation control system designed to address these challenges. The system integrates a capacitive soil moisture sensor, an ESP32 microcontroller, and GSM-based SMS communication to enable real-time, data-driven irrigation decisions without internet dependency. A relay-controlled actuator is automatically triggered when soil moisture falls below agronomically defined thresholds, while farmers receive timely SMS alerts. The system was evaluated through laboratory calibration and field-based experiments. Validation against gravimetric soil moisture measurements yielded a strong correlation (R^2=0.94), while classification accuracy across dry, moist, and wet soil states reached 95.6%. Experimental results during a 14-day tomato cultivation cycle demonstrated a 32% reduction in water usage compared to conventional fixed-schedule irrigation. The total hardware cost of the system is approximately $90 (₦77,400), and all design files, firmware, and calibration protocols are provided as open-source resources to support reproducibility and scalability. User evaluation involving eight smallholder farmers indicated high usability, timely notifications, and perceived improvements in crop health. This work uniquely combines embedded systems engineering with applied agronomy to deliver a scalable, affordable, and farmer-centric irrigation solution, contributing to sustainable water management in resource-limited agricultural systems..
- References
- Downloads
- Published
- 25-03-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Osagie I. IHENYEN, Raymond A. EKEMUBE, Development of an Agro-Waste Diesel Engine Powered Shredding Machine , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mukhtar N. YAHYA, Sohaib ALHAJHUSSEIN, Wastewater Analysis Using Kubota Membrane Bioreactor System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Mohammed A. GANA, Zaka A. MSHELIA, Isuwa S. AJI, Alhaji GUJJA, Lawan A.M. KOLO, Investigation and Comparative Analysis of Natural Moulding Sands from Five Deposits in Maiduguri, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Ndagi MAMUDU, Ibrahim S. MOHAMMED, Peter DANIEL, Timothy Y. AKANDE, Bala A. GARBA, Development and Performance Evaluation of Biomass Pyrolysis System for Biofuel Production , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Lawal B. IDRIS, A Review on Vehicular Ad Hoc Network (VANET) Security challenges and Solutions , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Yahaya U. JAURO, Danladi D. USMAN, Lawan G. ABUBAKAR, Yusuf G. SHIMBURA, Aminu MOHAMMED, Design and Fabrication of Tapered Screw Briquetting Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Bala I. ABDULKARIM, Yusuf M. BABA, Suleiman I. ENEHE, Kamoru A. SALAM, Umar IDRISS, Synthesis of Activated Carbon from Corncob for the removal of Lead (Pb²⁺) ions from Aqueous solution using a packed bed Adsorption Column , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Abubakar L. IBRAHEEM, John K. ALHASSAN, Noel D. MOSES, Suleiman AHMAD, Development of Ensemble SVM–LSTM Model for Phishing Website Detection , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Sati C. NSHOL, Saeed Y. UMAR, Suleiman A. YERO, Modification of the Engineering Properties of Road Base Course Soil Materials with Cement and Polyethylene Terephthalate (PET) , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Emmanuel O. AGBENYI, Adefope OWOJORI, Oluwadare J. AKINDUGBAGBE, Babatunde ADEBO, Chigbo I. OKEREKE, Impact Assessment of Natural Radionuclides in Cassava Tubbers Harvested from a Farmlands Around Quarry in Moniya Ibadan, Nigeria , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
Most read articles by the same author(s)
- Abubakar LAWAL, Abdulkadir O. ABDULBAKI, Nathaniel SALAWU, Bala A. SALIHU, Mamman A. THOMAS, Abraham U. USMAN, Sub-6 GHz Millimeter-Wave Metamaterial Antenna with Reconfigurable Radiation Patterns for Enhanced Wireless Communication , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Suleiman ZUBAIR, Hassan ABDULAZEEZ, Bala A. SALIHU, Abubakar A. SHUAIBU, Design and Implementation of a BLE 5.0-Enabled Wearable Finger Mouse Using the XIAO nRF52840 Platform , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
