From Local Sand to Functional Silicon: An Integrated Pathway for Producing Photovoltaic-Grade Material from Nigerian Silica Sand
- Authors
-
-
Tahiru MOHAMMED
Author
-
Muhammad B. MAINA
Author
-
Abba B. MUHAMMAD
Author
-
Muhammad SHUWA
Author
-
- Keywords:
- Silica sand, purification, carbothermic reduction, upgraded metallurgical-grade silicon (UMG-Si), photovoltaic, local content, Nigeria.
- Abstract
-
Nigeria's significant solar energy potential is constrained by a reliance on imported high-purity silicon, despite abundant indigenous silica sand resources. This study presents a complete, integrated experimental pathway to assess the feasibility of producing photovoltaic-grade silicon from River Alau sand in Borno State. The research encompasses: Comprehensive characterization of raw sand using XRF, XRD, and SEM/EDX; Purification via optimized acid leaching (acid was used to remove impurities) and calcination; Carbothermic reduction at a temperature of 1700◦C was carried out to transform the sample to a metallurgical-grade silicon (MG-Si) and subsequent directional solidification; Evaluation of the electrical and optical properties of the upgraded silicon; and Fabrication and outdoor performance testing of simple solar cells under Maiduguri conditions. The raw sand contained 77.63% SiO₂ with significant impurities (Al₂O₃: 2.10%, K₂O: 6.31%). Purification achieved ≥99.6% SiO₂ purity, reducing key metallic impurities to <0.1%. Carbothermic reduction yielded MG-Si with 78% efficiency, and the upgraded material exhibited suitable properties for PV applications: a resistivity of 4.2 Ω•cm and a band gap of 1.12 eV. Fabricated solar cells generated an open-circuit voltage of 0.48–0.52 V. A preliminary economic analysis suggests a 25–30% potential cost saving in raw material sourcing. This work provides the first proof-of-concept for a viable domestic value chain from Nigerian silica sand to functional photovoltaic silicon, demonstrating technical feasibility and supporting the development of local solar manufacturing capabilities.
- References
- Downloads
- Published
- 29-06-2026
- Section
- Articles
- License
-
Copyright (c) 2026 FUDMA Journal of Engineering and Technology

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
How to Cite
Similar Articles
- Mukhtar N. YAHYA, Sohaib ALHAJHUSSEIN, Wastewater Analysis Using Kubota Membrane Bioreactor System , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Victoria A. UMEJURU, Isaac E. IHUA-MADUENYI, Adaobi S. NWOSI-ANELE, Performance Evaluation and Economic Assessment of Electrical Submersible Pumps for Heavy Oil Production in Mature Niger Delta Oilfields , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Opeyemi A. ASAJU, Cephas ADELORE, Akintunde O. ONAMADE, Jonathan B. ADEWUMI, Glory A. ODUBANJO, Gbenga O. WILLIAMS, Enoch O. OYELEYE, Assessing Thermal Comfort and its Impact on Student Satisfaction in Selected Hostels at Caleb University, Imota, Lagos State , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Zakariah A. ADEJOH, Hawawu SALAMI, Abdullahi M. EVUTI, Yahaya S. MOHAMMAD, Yakubu STEPHEN, Effect of Activation Time on Physicochemical Properties of Activated Carbon Prepared from Coconut Shell , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
- Olusegun A. AFOLABI, Olanrewaju A. OLANITE, Nsikan L. AKPAN, Design and Simulation of a Synchronous Reference Frame-Based Active Power filter for Harmonic Mitigation , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Titilope A. BANJOKO, Bilkisu L. MUHAMMAD-BELLO, Predicting Requirement Change Using Bayesian Networks on Historical Traceability Data , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Michael R. ADU, Blessing O. UMUKORO, Design and Construction of a 1.5 kVA Pure Sine Wave Inverter for Office Use , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Yahaya U. JAURO, Danladi D. USMAN, Lawan G. ABUBAKAR, Yusuf G. SHIMBURA, Aminu MOHAMMED, Design and Fabrication of Tapered Screw Briquetting Machine , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Afeez A. AWOLOKUN, Olusegun O. ALUKO, Temitope F. AWOLUSI, Mayowa A. OGIDI, Performance Evaluation of Pervious Concrete Containing Glass Cullet and Glass Powder for Sustainable Construction , FUDMA Journal of Engineering and Technology: Vol. 2 No. 1 (2026): June 2026
- Zainab B. LAPAI, Joseph A. OJENIYI, Ismail IDRIS, Abdulkadir O. ABDULBAKI, Jennifer BALA, Entropy-Guided Neural Architecture for Family-Level Classification of Windows Ransomware , FUDMA Journal of Engineering and Technology: Vol. 1 No. 2 (2025): December 2025
You may also start an advanced similarity search for this article.
